GTDP280ED5WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from HAWLEY, PA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke
Snap off and then snap New one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAREN from THIBODAUX, LA
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
inherited machine, lint filter missing
Searched the sites order # online, called, ordered, delivered PDQ, unpackaged, popped in. That was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUDITH from FRUITA, CO
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My lint filter had a big hole in it. My dryer is 10+ years old.
All I had to do was remove the damaged filter and replace it with te new one. It could not ave been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffry from ROCKVILLE, MD
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burnt out bulb
Used a flash light to see, reached in and installed new bulb above the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from DOVER, AR
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken dryer door handle
removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from CONNELL, WA
- Parts Used:
- WE03X37320, WE03X37319, WE09X27634
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Black marks showing up on garments.
Once I figured out how to remove the control panel. The rest was very easy. Upon pulling off the knob in the center of the control panel, there was a screw behind it. Once removed I used the palm of my hand and gave it a couple of upward hits in the center while the door was open. It slid up and I removed the electrical connections. Then carefully removed the top by pushing from the rear of the machine slightly and lifted off. Then removing the screws that hold the front on . After that it went pretty easily, reassembly went in reverse and. That was that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from HAMILTON, OH
- Parts Used:
- WE4M325
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
When moving the dryer there was a loud pop and the dryer circuit breaker tripped.
When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from CORP CHRISTI, TX
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from WACO, TX
- Parts Used:
- WE2M302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Reversing the dryer door.
Removed 4 #1 Philips screws from 1side and add to the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff D from NEW MEADOWS, ID
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum would not turn
Exactly how your perfect video instructions showed me. Thank you for a job well done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from LACYGNE, KS
- Parts Used:
- WE01X20378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
knobs cracked
Push on. But one pushed in panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Renee from Leesburg, VA
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The dryer lint chute was cracked and catching our clothes.
We watched the YouTube video and had it installed in no time. Saved money doing it ourselves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from WILDER, KY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door handle broke
Called my son-in-law. Easy as pie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from LELAND, NC
- Parts Used:
- WE01X20378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The dryer would not turn on.
We took the knob off of the machine and it appeared to be cracked on the inside. We ordered a new one and received it in 2 days. We matched the inside of the new knob to the stem coming out of the machine and placed the knob on the stem. The machine was fixed and we were happy! Thanks Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from CHANUTE, KS
- Parts Used:
- WE05X20431, WE4M181
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer was over heating and shutting off after like 5 minutes, the back was hot to touch..got the cycling thermostat problem solved
4 screws to open it up,pull out the wheel and there it is on back . Pretty easy..
Was this instruction helpful to you?
Thank you for voting!