GTDP200EF3WS General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- bryon from ZEPHYRHILLS, FL
- Parts Used:
- WE4M533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
TIMER STOPPED MATCHING UP WITH WHAT IT WAS SET ON AT THE DIAL
JUST FOLLOWED THE VIDEO PROVIDED ON THIS SITE. VERY EASY TO DO WITH BASIC TOOLS, AND A FEW MINUTES.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEOMINSTER, MA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb was intermittently working
Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from EDGEWATER, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
take the old dryer lint screen out
Hand replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from DOVER, AR
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken dryer door handle
removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from EDGEWATER, FL
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My last phase of repairs of minor items.
if your unit has over 6,000 hours of operations, one needs to remove the front panel and inspect the sliders that the drum rides on. The video were very helpful to replace the sliders. Unfortunately, my dryer had over 10,000 hours of operations over a 30 years period, hence a major repair costing over $200.00 dollars. The drum sliders were gone, hence the drum eat through the plastic guides. More so, the drum started to eat away the front panel. If the dryer is eating your closes and making a noise, one is looking at a $200.00 repair job. Hence check the sliders early will save one $$$$.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from INMAN, SC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter had deteriorated
Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from CEDAR RAPIDS, IA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out
Unscrewed the old bulb using the lefty loosey method. Installed the new bulb by turning it clockwise or righty tighty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAREN from THIBODAUX, LA
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
inherited machine, lint filter missing
Searched the sites order # online, called, ordered, delivered PDQ, unpackaged, popped in. That was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUDITH from FRUITA, CO
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My lint filter had a big hole in it. My dryer is 10+ years old.
All I had to do was remove the damaged filter and replace it with te new one. It could not ave been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from JEWETT CITY, CT
- Parts Used:
- WE01X20376
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Timer knob cracked and no longer term center shaft of the time or just spot
Pull to remove old knob, push to install new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from KATY, TX
- Parts Used:
- WE4M533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Timer in Timed Dry cycle stopped at 50 minutes.
Unplugged dryer from wall.Removed 3 screws from the back that held the front face plate on. Pulled face plate away and to the right to release it from the dryer. Lifted the locking tab slightly and turned the old timer counter clockwise to remove. One at a time I removed a wire and connected it to the new timer. Installed new timer to the back of the face plate. Pushed on timer knob so I could hold the back of the timer to get it all the way on to the shaft. Lined up the three tabs at the bottom of the face place and slid it to the left , pushed the face face into place and secured it with the 3 screws. Plug Dryer back in. Done in less than 10 minutes. Dryer now works properly again. I know I saved myself a lot of money doing the repair my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bristow, VA
- Parts Used:
- WE03X37320, WE03X37319
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Rubbing noise while dryer was running.
After watching the video, the repair was very simple. There were no hiccups along the way. Special mention: the customer service is the best I've ever interacted with. Thank for making this a stress free experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffry from ROCKVILLE, MD
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burnt out bulb
Used a flash light to see, reached in and installed new bulb above the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dina from HILLSDALE, NJ
- Parts Used:
- WE01X20380
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Control knob spinning, could not get dryer to run.
My husband and I are the least repair-oriented people in the world. We can, however, follow instructions.
We were seriously trying to decide whether to call a repairperson or buy a new dryer, since dryer is over 5 years old, and it does not seem that appliances last any more. (New dryer: probably over $700)
Read about issue on PartSelect. Found clear and easy to follow explanations. Thought we needed a new timer, and considered buying one. Installation instructions seemed clear and simple enough for even us to do. Pulled off old timer knob to discover the back was cracked, which was why it was spinning.
Bought control knob. Pushed it on. Perfect!
Total time for repair: about 10 seconds
Total cost (including shipping) about $33
We were seriously trying to decide whether to call a repairperson or buy a new dryer, since dryer is over 5 years old, and it does not seem that appliances last any more. (New dryer: probably over $700)
Read about issue on PartSelect. Found clear and easy to follow explanations. Thought we needed a new timer, and considered buying one. Installation instructions seemed clear and simple enough for even us to do. Pulled off old timer knob to discover the back was cracked, which was why it was spinning.
Bought control knob. Pushed it on. Perfect!
Total time for repair: about 10 seconds
Total cost (including shipping) about $33
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from FARR WEST, UT
- Parts Used:
- WE17X22217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Bad dryer motor
Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .
Was this instruction helpful to you?
Thank you for voting!