GTD42EASJ2WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- rodney from VANCEBORO, NC
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt broke on dryer
good replacement procedure on you tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from NEW PRT RCHY, FL
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
evidently the pulley spring on video was very very very weak
the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Poughkeepsie, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Not Starting
First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matthew from HUDSON, IA
- Parts Used:
- WE04X24550, WE01X24552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Timer knob would not turn, caused the knob to break.
Remove two screws on the back of dryer that hold the Control panel on. The panel is hooked on to the dryer so carefully remove that. The timer knob has several wires hook into it so take a picture for reference. Remove the screws, remove and install new timer. Now transfer the wires over to the new timer one at a time to avoid confusion. Reinstall the the control panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DECATUR, GA
- Parts Used:
- WE03X37320, WE3M51
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Replace the front slides and glides on the dryer
To get to the slides, needed to take off the front panel, the top and then can loosen the front of the dryer. Pull it out enough to get to the slides and replace them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calder from WARNER ROBINS, GA
- Parts Used:
- WE01X24552
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Timer Knob was stripped
Just had to push it on. That's All.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GULF BREEZE, FL
- Parts Used:
- WE01X24552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob plastic fractured
Slip the replacement on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from WACO, TX
- Parts Used:
- WE2M302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Reversing the dryer door.
Removed 4 #1 Philips screws from 1side and add to the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel, J from MCALESTER, OK
- Parts Used:
- WE4M325
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Original terminal grounding block melted for unknown reason.
Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from GUILDERLAND, NY
- Parts Used:
- WE04X28977
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
The dryer would not start.
The entire dryer had to be taken apart to get to the door switch. I determined the door switch was faulty by measuring conductivity. I purchased the new switch which cost about $9. The shipping cost was $9. After all that, the dryer still won't start. I gave up and bought a new dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ATWATER, OH
- Parts Used:
- WE04X28977
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After closing dryer door unit would not start after several attempts.
Pry out switch with screwdriver. After removing switch unplug electrical leads from old switch. Plug leads in new switch and reinstall switch in dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gonzalo from Haines City, FL
- Parts Used:
- WE03X25576
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Noise when drum is spinning.
I removed the top and front panel with door. Removed the bearing top assembly and install the new one. Then I reinstall the front panel with door and top panel in that order. Plug and play!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from MC ARTHUR, OH
- Parts Used:
- WE01X24552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken dryer knob/wouldn’t connect to select cycle
Simply aligned the knob and put it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cary from SILVER SPGS, FL
- Parts Used:
- WE04X28977
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
When the door is closed the dryer didn't work
Easy watch YouTube and open door placed screwdriver under door switch pry lightly and switch will pop out unplug wire connectors and replace on new switch reinsert switch should be done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MILLEDGEVILLE, GA
- Parts Used:
- WE01X24552
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old timer knop cracked
stuck new knob on spindle.
Was this instruction helpful to you?
Thank you for voting!