DX4500GA3WW General Electric Dryer - Instructions

Open the door and removed the part. Installed the new part and started the dryer.

Un plugged dryer from wall - pulled off knob - Unscrewed 4 screws on top of panel - Opened panel by pulling it forward - Removed 2 leed wires - removed switch by turning switch counter clockwise - installed new switch put the wires back on and screwed the panel back on. Done deal.

Unplugged dryer. Removed four back panel screws to expose the switches. Removed the wires from the bad switch and transferred them to the new switch. Lifted locking tab on switch and rotated it so the two locking tabs aligned with the slots. Removed old switch and inserted new switch. Rotated about a half turn and replaced the four panel screws. Plugged in the dryer and tested. Very easy repair.

(1) unplug the power from outlet. (2) unscrew the 3 screws. (3)slide the front instrument panel slight right to remove it. (4) flip over the panel (5) remember the wire colors and their connections, and remove 3 wires (6) pull up the metal tab on the start switch a bit to unlock it and turn counter clock wise to remove the switch (6) do the reverse steps to install the switch.

It's no surprise that GE would use cheaply made parts in such a mass produced product, but it was irritating to see the start switch fail just fourteen months after purchasing the dryer. I am glad that a little thought was put into an easy snap and twist installation of the control panel switches. The original switch failed, due to arcing and pitting of the contact points no doubt, and the local parts house didn't even recognize the part, let alone have it in stock. Thanks to PartSelect.com I could have the part in just a couple of days!
The panel comes appart with just four star driver screws on top, but an allen wrench will work also. Wire jumpers with spade connectors are pulled apart and reattached with needle nose pliers.
In the mean time to keep the dryer operational, I did some creative "re-assigning" of some of the control panel jumper wires using the switch that controled the "Wrinkle Care" setting as a temporary Start Switch as it had the same current handling limits. By the way before attempting such a temporary bypass setup, consider not voiding any warrantee arrangement still applying to the product and have some basic electronics and safety knowledge, study the provided schematic well attached to the back panel and remember to write down all of the original wire connections. And when in doubt, calling a qualified GE appliance repair person is your best and safest bet.
New part went right in in about 15 minutes with original wiring restored and double-checked and the dryer is running right on que again.
Thanks PartSelect.com!

Removed 4 screws at the top of the dryer controls. Pulled the control toward me , pressed the pulled the tab on the switch up, turned the switch counterclockwise, removed the knob and the 4 wires, Plugged the wires to the new switch and reversed the installation

The part came today…and I installed it in 10 minutes. The only time consuming part was locating a torx screwdriver which was needed to remove the panel.
Lifted the panel, extracted the existing switch and
disconnected the wires and used a flathhead screwdriver to lift off the existing switch. Reconnected the new piece, and voila my dryer worked!
Your site is great!

Remove top control panel, disconnected wire from old switch to new switch (remover 1 wire at time so it would not get mixed up)twisted old switch out inserted new switch and replaced control panel now works like it should. I thought it might would be a safety issue is why I replaced it

My son is an engineer and repairs washers and dryers for a large commercial laundry company on a daily basis. He installed my part easily and had me up and running in no time.

Watched tecnician (I paid) as he diagnosed the problem. Four screws take of the top and front. Clothes drum slides out. Access to valve is good. Valve attaches to feed via compression fitting. Male end of fitting on unit is moved to new unit via allen wrench. Drive belt is re attached around drum and over idler easily. Part cost $90.00 shipp0ed to me. Technician asked $375.00 for this repair. Access the parts via placing the model number on Google Search.

Turned off breaker, rmoved back panel, removed timer, replaced knob. Put back together.

Took the front plate of the top of the dryer and then tried to fit the new switch. Unfortunately as there were no instructions on how to fit it my husband took the switch off the backing plate, and then realised his mistake. So he had to order another one. When that arrived it took all of 5 minutes to fit. It was an expensive and unnecessary mistake.

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

removed 4 screws from top of control panel. pulled 3 knobs off. removed face cover. unplugged damaged unit. twisted unit to right and removed. installed new unit. plugged in wiring. replaced panel. replaced screws and knobs.

the part fixed all the problems in a cinch