DBL333EB3CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from YARDLEY, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob and could not turn on dryer
followed the video you provided and it was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from MONROEVILLE, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken start knob
Just push knob on less than 4 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from SCOTTSDALE, AZ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My dryer wouldn't start, I saw the part on your website after reading comments from other people
I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from MANHATTAN, KS
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Start knob broke off
At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Cecil, WI
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Start knob was broken off flush with switch
I turned off the power, unscrewed the 4 screws from the top of the dryer. I then opened it and turned the switch that was in there counterclockwise exactly as utube video said to do. I then took off the two wires from the old switch. The rotary start switch fix right in where the old one was. I put the panel back together, put on the old knob and turned the power back on! It took less than 15 minutes from start to finish! If I can do it anyone can! Joanne Klinkhammer Cecil, Wisconsin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Marietta, OH
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Start switch broke
Followed the on line instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Ridgefield, CT
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken spindle which required a total switch replacement.
It took longer to vaccume the lint out of the machine than to change the part.
The part replacement is done without any tools.
My wife could have done it
The part replacement is done without any tools.
My wife could have done it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from lawrenceville, GA
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Timers are made to turn clockwise and break when turned counter clockwise
We are a retirement community and when we opened March '07 the company purchased GE washer and dryers to go in our common area laundry rooms for the residents to use. Because of their age, they will often turn the knob counter clockwise and not the right diirection which breaks the device which is not good. With in 3 days of installation they had broken 2 of the new knobs.
But, the ordering was simple, the shipment was fast and the install was quick for the maintenance tech.
But, the ordering was simple, the shipment was fast and the install was quick for the maintenance tech.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NICOLAS from LYNN, MA
- Parts Used:
- WE3X70
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Dryer making squeeky noise.
Removed the Drum and replaced the part....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from Atlanta, GA
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start switch broke off
I followed the video instructions. I did have to run to the hardware store to pick up a torx screwdriver but otherwise the instructions were perfect. I generally hire someone to do repairs, but this was too easy! I highly recommend doing this yourself as it is definitely a time and money saver. The website made ordering easy and the part arrived quickly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Valdosta, GA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The old knob hasd split and wouldn't turn the dryer on
I took the visegrip pliers off the d shaft and simply slid the new knob on with ease. I never doubted my abilities!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Middletown, NJ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Dryer Knob
Removed and replaced knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Sun City West, AZ
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Sticker Switch Worn Out
Simple replaced switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanie from Barlow, KY
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken start knob on dryer
old dryer knob had lost its spring and would not turn on. simply pulled old knob off and replaced by pushing new knob onto shaft. voila! saved myself a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Norfolk, MA
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
switha broke off
Removed old switch, replaced it with new
Was this instruction helpful to you?
Thank you for voting!