DBL333EB3CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jesse from Battle Ground, WA
- Parts Used:
- WE3X70
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was squeeking for a while, and then eventually just quit working.
Took the top and the front panel off (took me a while to figure this out without breaking stuff). Took off belt, pulled out drum, replaced bearing, and then I also had to replace the ball (attached to rear of drum, which slides inside the bearing).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Charlotte, NC
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer would not start
My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WASHINGTON, DC
- Parts Used:
- WE12X10009
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Two tips after you watch the videos (and video link)
Watch the videos for replacing the belt. The one by Kenmore is the most accurate even though it isn't GE -- the mechanisms are the same. Here is the link to the one I found most helpful: https://www.youtube.com/watch?v=G2wTmfurT5o
First: You don't need to pull the washer/dryer out at all. Leave it in place. You can put the belt around the drive shaft and get the tension pully in place by feel and inspect your work with a flasklight,
Second: There is absolutely no reason to spend $70 on a rubber belt. Other places sell it as cheaply as 10 dollars. Shop around -- the actual part is not at all impressive and should not be priced this high.
First: You don't need to pull the washer/dryer out at all. Leave it in place. You can put the belt around the drive shaft and get the tension pully in place by feel and inspect your work with a flasklight,
Second: There is absolutely no reason to spend $70 on a rubber belt. Other places sell it as cheaply as 10 dollars. Shop around -- the actual part is not at all impressive and should not be priced this high.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from coldwater, MI
- Parts Used:
- WE3X70, WE13X28680
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
load noise
took the top off, then the front,there 2 screws that hold the front on. there's a yellow thing on the front took that off, it is held on with one screw. on the back of the dryer on the bottom is a metal plate take that off, to get to the belt take that off. then there' 3 screws in the drum, take them off ,then you can slid the drum out. then take 2 screws off the bearing bracket, that's it. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from CAMILLA, GA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Start knob broke
Line up knob. Push on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Chanhassen, MN
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The control switch broke off flush from the start switch
My wife was attempting to start a load of laundry when the start knob came off in her hand. I figured the inside of the knob had broken loose and the stem from the rotary start switch would be sticking out, well the stem had broken off flush and the knob was fine. After ordering a replacement, I jerry rigged the broken one with a large screw driven into it and put it back in place, worked great, just had to put a screwdriver into the screw and turn it to get the dryer to start. I felt it was fine to stay that way but the wife insisted we install the new one to put the knob back in place. The new switch arrived very quickly and went into without a problem, just four screws to remove the panel, two wire connections and was working again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Garrison, NY
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
there was no problem
installation exactly how your directions told me on the computer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DERALD from Burleson, TX
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Switch was either stuck in start position or had to rotate full turn to start
Removed four allen head screws to expose inside of panel. Used flat blade screwdriver to raise spring retainer and turned switch counter clockwise to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frederick W from wall, NJ
- Parts Used:
- WE25X10001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Broken shaft in rear bearing
Take the top off and front off and disconnect the belt and lift the drum out and there it is . Easy and alot cheaper then new dryer and works like new .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Rice Lake, WI
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken start swithch from moving dryer
Removed top panel from dryer. Unplugged the 2 wires for swithch, rotated swith, and removed. Reversed the process. Put parts back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from SCOTTSDALE, AZ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My dryer wouldn't start, I saw the part on your website after reading comments from other people
I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alonso from MONTGOMRY VLG, MD
- Parts Used:
- WE12X10009, WE13X10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Rear bearing was broke
I like to fix , i have time and i just give me the chance to try , and i did it , i wish to pay less for the parts , but was a good feeling when the problem fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from MANHATTAN, KS
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Start knob broke off
At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ELVASTON, IL
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
On knob went bad
Took new one out of package, and push it on. 4 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from YARDLEY, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob and could not turn on dryer
followed the video you provided and it was easy!
Was this instruction helpful to you?
Thank you for voting!