Models > DPSB513EB0WW > Instructions

DPSB513EB0WW General Electric Dryer - Instructions

Jump to:

All Instructions for the DPSB513EB0WW
121 - 135 of 144
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jim from Summerdale, PA
Parts Used:
WE4M415
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer would run for 4 minutes and shut off. keep turning it on
Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Huntington Beach, CA
Parts Used:
WE03X37318
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer squeaking/squealing sound
After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RAMCHANDAR from BRISTOW, VA
Parts Used:
WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
noisey
TOO EASY to repair. WORKS GREAT>
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Mansfield, MA
Parts Used:
WE11M23
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
dryer was not heating up
Had to remove the drum to get at the heater element also had to swop the sensers to the new element
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alan from Cumming, GA
Parts Used:
WE4M415
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Dryer makes noise when "Start" is pushed, but stops when you let go.
Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Bruceville, IN
Parts Used:
WE14X25080
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
noise and not drying well
It was as easy as the repair film said it was . But after spending the money for the upper and lower baring seals I put it all back together and the motor started making a loud noise ? I took the drum and everything out and started the motor without the drum just the motor was running and the danged motor is going out now !I checked the price of a new motor its not to bad but with all of the parts I have put in this thing I could have paid part of what it would have cost for a new dryer ! I put it all back together and hope it last long enough to at least recoup some of what I have spent ,But the new parts work good !
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from Surfside, FL
Parts Used:
WE4M325
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Terminal block was burned
Before removing the old part,took photo with my phone camera to document the color wires hook up. Screwed in the new part and hooked up the color coded wires using the photo as reference. I was surprised how easy it was. Thanks. Partselect gave me fast shipping, cheap price and great customer service.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Garrettsville, OH
Parts Used:
WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Drum wobbling and thumping
Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gilbert from Torrance, CA
Parts Used:
WE14X25080
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
The plastic grid behind the lint filter started cracking with pieces breaking off. This caused delicate clothes to get tangled and twirled on the broken pieces.
I watched the installation video a of couple of times and followed the instructions. Two screws under the dryer door then the top comes off. Then two screws hold the front on come out. Unplugged the two wires to the switch. Removed the duct assembly. Cleaned up the door and snapped in the new duct assembly. Re-installed the door and then the top. Everything was easy - just like in the video.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fred from Falls Church, VA
Parts Used:
WE4M275
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Dryer would run but not heat
I opened the unit by removing the two screws over the door, lifting the top (careful not to break the plastic tabs connecting it in the rear to the electronic control panel), then removing the two screws securing the front so I could slide the drum forward and out (hoisting by the belt, bending the sides out slightly). I tested the heating elements for continuity, and tested the two thermostats on the left and right of the heating element for continuity. I found the wiring diagram in the control panel with the specs for the thermistors, which said they should read about 100 kOhm at room temperature. The two on the heating element were OK, but the thermistor on the back of the plastic output box read only about 6 kOhm. After ordering and installing the replacement, it took about 15 minutes to put the drum back in, re-thread the belt, and close the unit back up (thanks to some helpful videos on YouTube). This was the second time this thermistor failed! The first time was under warranty.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DPSB513EB0WW
121 - 135 of 144