DWSR405GB1CC General Electric Dryer - Instructions

Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

Verified start switch was defective by jumping around switch to confirm the unit operated. replaced the switch.

Just like the other stories, remove the top and front of the dryer, replace the bearing and slides (or slides only if needed). I ordered only the slides, but also needed the bearing because I didn't realize the drum had worn through the bearing already.

All is necessary is remove 3 philip screws, remove the switch knob, lift a tab on the switch, rotate the switch counterclockwise and it was out. Pull wires off switch and immediately put them on the corresponding terminals of the new switch before reversing the above steps. Simple!!!

Imagine that!! Move 3000 miles from home to home and after 90 days in storage, we finally get our things. First the washer, then the dryer. Test, no water, okay...Open valves. It's like magic. Hmmm. Plug the dryer in. No sound, not a peep. Turn the start switch one more time, crack-crack, the knob falls in my hand. Ordered the part and got in 2 days. A few star bolts to remove, unplug 3 wires and presto, it works like magic. Thanks!!!

Started out by unplugging appliance then pulled off knob, removed 4 screws that held cover in place, removed wires from switch, rotated switch to remove. reversed steps to replace.

Pulled power plug. Removed the "Start/Stop knob" Removed 4 starbit screws across the top of the control panel. Flipped control panel down(toward front of dryer)to expose swithes. Aligned the new switch next to the switch being replaced, removed a wire and re-installed on the new switch. I did for each wire. To remove old switch, rotate counter-clockwise and lift out. Line up slots on new switch to panel slots, push down and rotate clockwise to lock in place. Re assemble panel, line up slot on switch knob to switch shaft and press on.

I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier

I followed the great tips from the other repairs and that part was easy. Turned out not to be the exact problem. The problem was the rear bearing shaft which in another 20 min I had the drum out and repaired. Now the dryer is like new and will hopefully last another 5 yrs.
Thanks Parts Select for your help!

Looked up the problem and solution on the web and,ah-ha, drum slides should be the cure. Easy to install, . Back to the internet to discover that after the slides, the bearing and felt liner were the next likely culprits. Again easy install, but to no avail. Calling in the pros.

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

snap in snap out

r/r parts unit runs great