DBLR333EG5CC General Electric Dryer - Instructions

inserted the lint catcher into the opening to replace the old one

With the help of doityourself guy on the internet

Did repair as per the video except I did not disconnect wires, just swung front panel around. Only complaint...discovered parts were much more expensive than other sites.

Open Door /remove 2 screws in top of door opening (this releases the top panel) /Lift top panel off of dryer (it is tucked under control panel) Remove the white plastic "arch" (front drum bearing) on top of door panel / Install new drum bearing and 4 each of the "slides" on the bearing/ There are two on each side of the "front drum bearing"/ Reverse the disassembly process to finish/ . You'll need a standard flat tip screw driver and a Phillips heads crewdriver to do all work

looked at video of dryer disassemble, replaced 4 bearing slides, reassembled. Dryer is perfect now , no noise. thank you for your parts.

First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.

Followed the directions but met resistance when the
timer could not be slipped off the "peg".
This timer was installed with a very small screw to remove
and install the new timer.- Thus, called an electrician
who had the very small screw driver to install the timer!
So $$$$$$$$$$. unhappy about this!

I followed the video on how to repair

had a great video to follow, made it easy to install.

I pulled the dryer away from the wall, I unplugged it, I took the back of it off, I removed the piece the timer, I marked on a piece of paper how to put it back together, I followed the instructions how to put it back together, I push I plugged it in, pushed it back into the wall turned it on bingo. Bingo dryer is working.

Handyman installed the finally correct switch. It was not the starter button.
This company was wonderful. Replaced each part without charge and rushed the replacements to us. Can' say enough good things to thank them for their courtesy.

The instructions that came with the bearing were limited and the illustrations were too dark to see. However, after reading the reports of others on this website, the repair was very easy.

Prior to disassembly, remove theaccess panel on the rear of the dryer. Pull the belt drive pulley arm up and the belt will easily slide off of the motor pulley. The belt can be left on the drum.

Then, remove two screws at the inside top of the dryer door. The top of the dryer will then lift up at the front and slide forward to remove. This will allow you access to two bolt head screws on each side of the front panel. Remove these two screws and then lift the panel slightly up and forward. The front panel will then be free and the dryer drum will slide forward and out. Remove the four bolt head screws (behind the electric elements) from the heater element on the inside back of the dryer box.

You can now exchange the bearing on the drum and the bearing insert on the dryer heating element simply by removing the old and reinstalling the new just as the old was removed - four screws for each.

You will need an assistant to re-install the bearing. Someone needs to hold the three pieces behind the drum as you insert the three screws. You'll also need a star wrench set for this.

The drum is easily reinserted - just be careful to get the front of the drum placed into the front bearing surface when reinstalling the front panel. One word of caution, My wife tried to remove the felt bearing on the bottom of the front panel thinking that it was lint.

I found that the inside of my ten year old dryer was unbelievably full of lint. I'm sure that the efficiency improvements by cleaning the air passages will be substantial and I've just saved $400 on the price of a similar dryer ($900 if my wife and I decided to upgrade to the "new" model that we wanted but really didn't need.

Drum was misaligned and scraping againt the appliance housing due to worn-out slides.

Replaced the drum slides 2 - white, 2 - black. Replaced the slide housing (front drum bearing?). This part was worn due to worn-out slides that were missing.

Cleaned out old lint from rear of drum and appliance housing. Put new weather stripping seals on the lint catch exhaust. Checked drum belt for cracks and checking.

Buttoned everything back up and dryer works as good as new. $60.00 for parts, 1 hour labor and the job was done!

I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair

Removed top - 2 screws. 2 more and the front comes off. I left the wires connected, and leaned the front against the wall. I then popped the drum bearing, with the slides off of the front, and pulled the felt from the lower half. I took some extra time cleaning lint with a shop vac. I then assembled the new parts back onto the front, and pulled the felt into position - it was a little fussy getting it right. The front panel and the top go back, and it`s done. I am glad I ordered the drum bearing, as the felt was worn much more than I would have guessed. This job could probably be done in 15 minutes next time, not including lint clean-up.