Models > DNSB514EB0CC > Instructions

DNSB514EB0CC General Electric Dryer - Instructions

Jump to:

All Instructions for the DNSB514EB0CC
106 - 120 of 135
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jim from Summerdale, PA
Parts Used:
WE4M415
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer would run for 4 minutes and shut off. keep turning it on
Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Huntington Beach, CA
Parts Used:
WE03X37318
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer squeaking/squealing sound
After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Bruceville, IN
Parts Used:
WE14X25080
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
noise and not drying well
It was as easy as the repair film said it was . But after spending the money for the upper and lower baring seals I put it all back together and the motor started making a loud noise ? I took the drum and everything out and started the motor without the drum just the motor was running and the danged motor is going out now !I checked the price of a new motor its not to bad but with all of the parts I have put in this thing I could have paid part of what it would have cost for a new dryer ! I put it all back together and hope it last long enough to at least recoup some of what I have spent ,But the new parts work good !
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shauna from Bend, OR
Parts Used:
WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
High Squeaking noise
I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Gig Harbor, WA
Parts Used:
WE01X20580
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old door handle broke off
Inserted replacement door handle into two slots on door and snapped into place. Amazingly easy and a perfect fit!
Was this instruction helpful to you?
Thank you for voting!
Customer:
jeffrey from hertford, NC
Parts Used:
WE03X37318
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Loud Squealling noise from dryer
Opened the door and removed 2 screws from inside/top of door. Removed top and then removed 2 screws from back of front panel. Lifted drum slightly to remove front panel and attached new slides.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dana M from Middleport, NY
Parts Used:
WE03X37317
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Intermittent Squeek Noise
Removed 2 screws from inside door lifted top panel up,removed 1 screw attaching front panel to left side. Pulled front panel out far enough to remove and replace slider bearing.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Pascagoula, MS
Parts Used:
WE05X20431
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Replace light bulb in drum.
Unplug dryer, unscrew bulb then replace with a new bulb. Plug dryer back in.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Angelica from Fayetteville, NC
Parts Used:
WE03X37317, WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Horrible squeaking noise during operation
The only tool used was a phillips head screwdriver. I removed two screws to lift the lid and two more screws to free the front panel, slid off the front panel, and had direct access to all 4 slides, replaced, reassembled, and good as new.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip from The Villages, FL
Parts Used:
WE01X20580
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Door handle had broken off
Replacing the door handle was a "snap" literally. All I needed to do was remove the handle from its plastic wrap; line up the inserts on the handle with the holes in the door and snap it in place. It was that simple.
Was this instruction helpful to you?
Thank you for voting!
Customer:
angela from Delaware, NJ
Parts Used:
WE03X37317
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
horrible shreaking noise
follow the video, and in no time fix and ran smooth, like brand new, love this website, fast and reliable
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from LIncoln, NE
Parts Used:
WE03X37317, WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Intermittent squeak when first starting the dryer.
Followed the video on this site but did not have to remove wires. Just stand in front and let the front panel rest on your leg while you replace the slides. Quick and Easy!!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carol from Bristolville, OH
Parts Used:
WE03X37317
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Screeching noise when drum went around
To get to where the drum slides go you have to first remove the dryer top. Then you have to remove the two screws that hold the dryer front/door. Found inside the dryer about an inch down on both sides. Be careful because it will fall off. Lower carefully as there is an electric hook-up on the bottom of the door. On the door top are the brackets that the slides slip into. My dryer has 4 slides. Sold individually for some reason. You are done except for re-assembly. Slip dryer drum back on door, press the front until you hear it click back together. Put screws back in and top back on. You are done and no more screeching!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carlos from Saint Albans, NY
Parts Used:
WE05X20431
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Blown bulb
Replaced bulb.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Houston, TX
Parts Used:
WE01X20580
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broken handle
Snapped right on! No problem.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DNSB514EB0CC
106 - 120 of 135