Models > DNSB514EB0CC > Instructions

DNSB514EB0CC General Electric Dryer - Instructions

Jump to:

All Instructions for the DNSB514EB0CC
76 - 90 of 135
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jeremy from Wexford, PA
Parts Used:
WE03X37318
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Loud squeaking sound from dryer drum.
Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Williston, VT
Parts Used:
WE03X37318
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer squeaks and squeals while running
Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Julie from Sterling Heights, MI
Parts Used:
WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
worn dryer drum slides
i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Laurie from Lawrenceville, GA
Parts Used:
WE05X20431, WE03X37318
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Very Loud Noise.
Took the front & top off the dryer. Saw that the slides were missing or broken. Got the parts and put it back together. Works great.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Christopher from Winsted, CT
Parts Used:
WE03X37317, WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
loud squeaking from dryer
Just like the other stories, remove the top and front of the dryer, replace the bearing and slides (or slides only if needed). I ordered only the slides, but also needed the bearing because I didn't realize the drum had worn through the bearing already.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Keli from Manassas, VA
Parts Used:
WE03X37317
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Dryer made hig-pitched screech
Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from Lynchburg, VA
Parts Used:
WE03X37318
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
Drum squeaked and occassionally would not turn, even though the motor ran.
I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nate from Affton, MO
Parts Used:
WE11M23
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
Dryer runs but does not heat
My dryer would run but not heat and the timer would not advance. PartSelect helped me determine that the heating element needed to be replaced. I have very little experience with appliance repair. I found this to be challenging but well worth it.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Richmond, VA
Parts Used:
WE4M415
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers
Dryer would not turn on
It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Highlands Ranch, CO
Parts Used:
WE03X37317, WE03X37318, WE1M462, WE1M461
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set
Dryer would not heat
Originally ordered heating element kit, but decided to replace drum slides and "o"-ring while the dryer was dis-assembled.Replacing the dryer elements was relatively easy-just follow instructions. Replacing the slides and o-ring was very easy, just clip in place. The dryer vent was almost totally clogged and probably the cause of most problems. This took longer than all mechanical repairs as I have a long dryer vent. I suggest cleaning the dryer vent regularly to avoid problem. I used a 4" circular brush and cordless drill to clean the duct. If you have not cleaned your vent in 2-3 years, you will be amazed at the amount of lint build-up. I was very pleased with the price of parts and customer service at Parts-Select, estimate I saved approximately $250-300.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from spokane valley, WA
Parts Used:
WE03X37318
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set
grinding noise -- sudden onset
I followed the varied instructions out there for getting the dryer open. WATCH the videos on uTube; I took out more screws than needed on first attempt -- which isn't a big deal but took me longer than it should have to pull it apart. It appeared the grinding was coming from the dryer bearings due to some abrasion I could see and worn front slides, so I replaced the front slides (4) and the rear bearing. The kids helped by crawling inside the drum to tighten the new bearing bolts (just for fun). When I put it back together it was making a somewhat different grinding noise. It wouldn't make any noise until I put the belt AND front cover on and then it would make a periodic (about every 10 degrees) grind when I rotated the drum; I took it apart and the grinding would stop even if I rotated the blower by hand. Put it together, the grind would start .... It took me awhile to figure out that the blower retaining bolt had come loose so the plastic blower was grinding on the metal cover. CHECK THE BLOWER RETAINING BOLT visible from the front with the dryer door/cover off -- it's not obvious that it's loose by looking at it since the retaining clip still sits over the blower shaft even when it's loose. You might even see small nicks in the blower fan blade. It's super quiet now.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Phillip from Lafayette, IN
Parts Used:
WE03X37317, WE03X37318
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
squeaked & I had already replaced the parts once
Unscrew the top panel parts three screws. Then another three or six screws to get to the dryer front which needs only to lift straight up about two inches. Pull back slightly and replace the teflon slides. To replace the slides they lay on a tiny plastic pin and slightly bend into the slot to hold them in place. Reseat the dryer drum. Reverse the process to make it like new. From the time you start hearing the dryer squeak, BE CERTAIN to replace these within a week or two (depending on usage.)Otherwise, you may wear out the housing where the teflon would rest. If that happens, you will be out more money to replace the housing and a lot more time to install. Been there and done that. Trust me.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from Baton Rouge, LA
Parts Used:
WE03X37317, WE03X37318
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Clothes would get caught in the drum slide
The clothes would get caught where the drum slide should be (it was almost totally worn down) and would leave black marks. I watched Parts Select youtube video. Bought the parts needed from Parts Select. They arrived within a couple of days. I replaced the 2 drum slides and no more getting caught. Took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Mansfield, MA
Parts Used:
WE11M23
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
dryer was not heating up
Had to remove the drum to get at the heater element also had to swop the sensers to the new element
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alan from Cumming, GA
Parts Used:
WE4M415
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Dryer makes noise when "Start" is pushed, but stops when you let go.
Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DNSB514EB0CC
76 - 90 of 135