DDC4500SQMWH General Electric Dryer - Instructions

It went perfect , just put it in. No tools needed.

inserted on an angle and snapped in place.
The best part of this story was I ordered the part on a Saturday and got it on Monday evening.
The repair took less than 20 seconds. I am extremely impressed with the fast fast fast shipping time.

I ordered the part via the internet. The shipping date was delayed twice but you excellent customer service department followed through and expedited the order. I installed it myself. Thank you.

Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

I love the Partsselect.com youtube videos. The man in those videos rocks!!! I did the repair of my rear drum bearing kit exactly as he showed me in his video and it was perfect. I have spread the word on facebook and around work about Partselect.com and friends and coworkers are already checking it out. Hey, everyone loves a good thing. I suggest that you do not be afraid, you CAN do it. Tear that baby apart and save yourself some money.

The dryer made a loud squeal and I shut it off immediately.
1 - Unplug the dryer
2 - Took the top off and the front off the dryer
3 - Removed the 4 Front Dryer Drum Slides that were worn all the way through
4 - Pulled the bunched up Felt
5 - Vacuumed out the inside of the dryer -Very Important
6 - Put the drum slides in and felt piece
7 - Put the front on top back on
8 - Worked great

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

First I removed the front and top panel to the dryer. I then popped of the drum bearing, popped the new one on, added slides and put the top and sides back on. Turned on the dryer and it works just like new. All for less than a repair man would come out on a call for.

This dryer uses pieces of slippery plastic on a plastic support attached to the dryer front as a drum bearing. Over time the slippery plastic wears out and the underlying support will wear through like mine did.
To replace this, first unplug the dryer and then remove the two screws inside the top edge of the door opening to free the top of the dryer cabinet. You may want to remove the door first for easier handling. Next lift up the cabinet top and pull it free to expose the drum and bearings. The front of the dryer is held on with two screws at the top front corners, remove these and tilt the front forward to expose the drum bearings. remove any remaining plastic sliders and pull the old bearing support free, stating at the top and watching out for the light bulb if present. Then install the new bearing support and replace the sliders. Now tilt the front panel back into place, guiding the bearings into the drum and lining up the tabs and slots. Replace the screws, this requires some fiddling to get the alignment right, then work the top panel back into place, reinstall the screws in the door opening and replace the door if it was removed.

The top and front of the dryer had to come off, and taking off the top (and later putting it back on) was the hardest part. The old seal was stretched approximately two feet longer than the replacement part, and its thinness caused the drum to squeak as it scraped by the door panel. We simply pressed the new seal into place after pulling out the old one. Piece of cake. Putting the front of the dryer back on was simple as well. Fitting the top back into its slots properly was the biggest pain of the whole ordeal. The part came in about 2 days. Thanks!

Removed Two Screws securing top of dryer to front of dryer. Removed 4 screws securing button panel to back of dryer. Removed top and set it to the side.
removed 2 screws securing front to sides and removed front of dryer, leaving electrical connectors connected. Removed old felt from lower drum support and removed old worn out upper drum bearing(only one slide was left). Snapped new drum bearing into front, installed new slides on drum bearing and new felt. Reinstalled all components in reverse of dismantle and fired her up. Works like a charm. My children hated the electrical dryer I was using in interim.

Basically, I ordered 2 slides the bearing and the felt, all of which I was told were "usually" the cause of the noise issues. I believe they were, I replaced them all and it runs quiet as a church mouse! Thank you for all the help..

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.