HTX24EASK1WS General Electric Dryer - Instructions

Replace both micro switches.

When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.

After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.

I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.

I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.

The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.

The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.

Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.

Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.

Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.

I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!

Removed 4 #1 Philips screws from 1side and add to the other side.

Pry out switch with screwdriver. After removing switch unplug electrical leads from old switch. Plug leads in new switch and reinstall switch in dryer.

Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.

Exactly how your perfect video instructions showed me. Thank you for a job well done!

Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.

It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.

If I were to do it again, it would take 30 minutes or less.

Once I figured out how to remove the control panel. The rest was very easy. Upon pulling off the knob in the center of the control panel, there was a screw behind it. Once removed I used the palm of my hand and gave it a couple of upward hits in the center while the door was open. It slid up and I removed the electrical connections. Then carefully removed the top by pushing from the rear of the machine slightly and lifted off. Then removing the screws that hold the front on . After that it went pretty easily, reassembly went in reverse and. That was that!

Follow the instructions from YOUTUBE to replace the new drive belt..

Remove top cover and front cover

loosened two hose clamps and four screws to replace the anti siphon valve.

Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.

Un plug the dryer. Gather phillip, flat head and torix screw drivers. Remove the rear of the dryer to get the spec sheet with the appropriate part number. Next called for part. Belt installation requires removal of front and top of dryer in order to slide belt over the drum. Getting to all the fastners requires tilting the dryer on its back. Clean out excess lint from dryer interior and duct work. Slide drive belt over drum and use some masking tape to hold it in position. Reassemble dyer. Return dryer to upright position and put the belt on the pully and tensioner from rear access port. Remove tape. Replace access panel. Reattach vent duct work. Plug in. There are 5-6 different size screws holding everything together...you may want to use masking tape to label where each type of screw goes. All totaled it took about an hour and cost less that $25. Well worth the effort.

4 screws, that was it

open the dryer door, locate the 2 screws that hold the top in place, unscrew them

then locate the 2 screws (located near the top of the dryer (facing toward you) and unscrew them

allow the front of the dryer to tilit out towards you, replace the felt, slide the drum back into place into the front of the dryer, resecure the 2 screws (removed last)

lower top of dryer back in place, being careful to make sure the top clips back in correctly.

re-install the 2 screws that secure the dryer top to the front.

boom, you are done....

Amazingly easy work...