HTX24EASK1WS General Electric Dryer - Instructions

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

Lift the lint filter and slide the 2 hooked ends into the 2 holes provided . Front end is locked in as other end is suspended .

Originally I thought that the Start switch was the issue, and ordered one. After taking the machine apart and running some tests, the issue was clearly not this switch, but a different switch that cuts power when the belt tension is no longer being applied to the idler pulley spring. I fixed this by bypassing this switch, which in my opinion, is error prone and serves no purpose. The switch can be accessed by removing the control panel, then top cover, then front cover, then drum. The bogus switch is screwed to the bottom left, near the motor. The idler pulley spring rests against it. Just disconnect the switch wires, then clip, strip and crimp then together to bypass the switch, and voila! Now if the belt breaks or comes off the pulley, the motor will continue to run, but you wont hear the wet clothes flopping around, so that will be the indication that you have a belt problem. Hope that helps!

Check for 240 at back of dryer, replaced all three thermostats around coil on rear panel, including high limt thermo,, but still no heat.

Not sure if coil is bad or if there is another thermostat or fuse around blower.

Found the dryer's high limit thermostat had opened up.
Likely cause was excessive lint buildup in exhaust vent pipe to outside.
Used wire nuts to "temporarily" bypass thermostat and cleaned out the vent pipe
When new part arrived...

Removed control panel screws and panel was laid on top of dryer
Removed back panel screws.
Removed top panel screws. Lifted to allow right side swing out slightly.

I did not have sufficient tool to reach the thermostat therefore I reamed out a hole in the rear panel above the thermostat fastener screw to allow a long handle screwdriver into the area for replacement.

Removed temporary bypass and used wire nuts to utilize dryers' thermostat existing wiring.

Took out interlock switch (two leads) and replaced with new one. As simple as that.

After checking the obvious things such as household circuit breaker and verifying that the dryer power outlet did indeed have the proper voltage supply, I started troubleshooting the dryer itself. The "partselect.com" website has a lot of good troubleshooting information. I used it to narrow my search and began by checking the fuse located where the power cord connects to the dryer. From there I used the information that the website provided for finding and checking the overtempt switch for the dryer. It's located in a very hard position to get to, and it was indeed bad. I ordered a new one from the "partselect.com" website and started checking my dryer exhaust vent hose for a blockage, as that was the most practical cause for the overtempt switch to fail. Once I verified that the exhaust was clear from any obstruction, I set my sights on removing the bad overtempt switch.

I have over 30 years' experience troubleshooting and repairing both AC and DC electrical and electronic circuits and systems. I'm 6'4" and have very big hands and it was next to impossible for me to get my hands in a position to loosen and remove the 1 screw that was holding the switch in place. After an hour or so I was finally able to remove the switch. There was no way that I was going to be able to successfully install the new switch due to the lack of space. I ended up going back to the "partselect.com" website to see if anyone else had this same issue and found a way to overcome it. After few minutes of reading thru different installation comments from other people, I found one that had the key to quickly and accurately installing the switch. This person used a drill and drilled a hole in the back panel of the dryer to gain access to the screw that holds the switch in place. So, I drilled a small 1/8" hole in the back panel directly across from where the head of the screw was. I used several more drill bits and worked my way up to a 1/2" sized bit. Then, I used a 1/4" drive socket set with a 10" extension and 1/4" socket to install the screw retaining the switch. I reassembled the dryer and have had no other trouble since.

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat

removed old lint trap cleaned excess lint that fell inside from the broken lint trap made it easier for new lint trap to slide in.

Took the front panel off. 2 screws on top of the front panel when you open the door, 2 right next to the door opening. Next gently pry up the top panel in the front of the dryer to remove 2 black screws in the front corners. Now the front panel can gently be pulled back and then lift up and the frpnt panel can be put to side. Now you have acces to remove and replace the drum bearing glides. They just clip in. Also a good time to inspect the belt and clean out the dryer.

Replaced the rear drum bearing, Front drum bearing,front bearing tabs and belt. I replaced the belt from the front of dryer. Better to go thru the back. Much easier.

Follow YouTube "how to change dryer's belt" some video is very clear.

If your dryer is making a grinding or loud plastic rubbing noise, you likely need to replace the slides. Here is how I did it.

TIP: Before beginning, set out a hand towel on the washing machine to set the screws onto, in the order and position you removed them.

IMPORTANT: Before beginning, turn off the gas to the unit and unplug it! This repair is all done from the front side of the machine, so you should only need to slide it out enough to unplug it.

Step 1: Remove the control panel

To do this, you need to pull out on the round silver control knob to remove it. This will expose a long screw. With the long screw removed, grab the panel with both hands and slide it straight up. Be careful, the control board is still connected with a 40-pin ribbon cable. Set the control board on top of the dryer temporarily.

Step 2: Remove the lid

There are three screws to remove the lid. Remove them and set them on the screw holding towel. The lid is attached at the back, so to remove it you need to slide it forward towards the front of the unit. Once the lid is loose, you can have a helper hold the control panel while you set the lid aside, or gently let the control panel dangle.

Step 3: Disconnect the control panel and wiring harnesses

Gently pull on the 40-pin ribbon connector until the control panel ribbon cable is removed. There is a notch to designate which direction the ribbon cable it goes back in. Set the control panel to the side. At the same time, you can disconnect the two wiring harnesses that feed the door light and sensor. These wiring harnesses are secured to a silver plate with a zip tie. Cut the zip tie with your diagonal cutters. (You can trim the old zip tie and replace it by feeding the extra small zip tie through the original opening later.)

Step 4: Remove the steel plate that the wiring harnesses were attached to

There are 6 screws to remove the steel plate. Pay attention to where the extra large head screws go, because these are what the control panel slides onto, when you put things back together. Pull out on each side to release the bottom clips, then slide it upwards. Set this piece aside.

Step 4: Remove the front panel (the door panel)

There are 4 screws to loosen the door panel. Two silver screws at the top, and 2 white screws at the bottom. Loosen the white screws about half way. These do not need to be completely removed because the door can rest on them. Remove the top silver screws. Gently lift the dryer drum off the front bezel while you tilt the front panel towards you. At this point you should be able to see the white and dark green slides. I found it easier to lift the front door off the white screws and set it up against the wall.

Step 5: Replace the slides

The slides have plastic hooks that go through the round holes on one end to hold them in place. You should be able to remove the slides with your fingers (maybe with a little help from a flat-head screwdriver), and replace them. There are dozens of YouTube videos on how to do this if you need help. Be careful not to break the plastic hooks that hold the slide to the front plastic bezel. Replace white slides with the white, and the dark green slides with dark green.

Step 6: Putting it all back together

Do everything in reverse. Set the front panel in the white screws, lift the drum, and slide the door panel back to rest on the slides while you put back the silver screws. Give the drum a few good spins manually to make sure there isn't anything still rubbing. Keep in mind the sliding noise is slightly louder than normal until all the panels are replaced.

It will help the process to only tighten the screws half way while putting them all back in. Once everything aligns, then you can tighten them down. DO NOT over tighten, use hand tightness only or you will strip them out. With the front door panel back on, you can put the steel panel back in place. Once you have the 6 screws done, remember to slide a small zip tie through the previous hole to secure the wiring harnesses. Connect the harnesses, and the front panel ribbon cable before putting the lid back on. Insert the screws to the lid, then slide the control panel back down, and replace the single long screw. Note that the control knob is notched, so align the flat sides as you put it back in.

Plug it back in, and turn back on the gas, you are done!

UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.

The video on the site is easy to understand and a snap to follow.