GTMP280ED6WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christopher from Miami, FL
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
dryer cylinder wouldn't turn
Pryed off the top with a flat head screwdriver and removed the 2 screws holding the front panel to the sides. Then lifted the front panel off of the bottom brackets. Belt fit perfectly and followed the provided instructions to loop it around the motor and pulley. PartSelect got the part to me within a couple of days and the repair was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Charleston, MS
- Parts Used:
- WE03X29897, WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken belt
Removed the top of dryer two screws behind door at top then removed top two screws top corner lift dryer tub put belt around the tub then looped belt around the pullies.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nancy from silsbee, TX
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bad light socket
unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to do it myself. easy easy easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Curtice, OH
- Parts Used:
- WE4M415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The Dryer would not start
Doing some simple troubleshooting with the volt-ohm meter I determined that the door switch was failed.
The replacement door switch restored the motor circuit keeping my dryer in action.
The replacement door switch restored the motor circuit keeping my dryer in action.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Meridian, ID
- Parts Used:
- WH01X10302
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken belt.
Used 1" puddy knife to depress spring loaded retainer tabs. Front panel is removed by prying the top of the front panel away from the machine. Lift front panel to release bottom from machine. Set panel aside. New belt is installed by placing it on the drive pulley and then rolling belt onto the motor pulley. Rotate the motor by hand while moving belt so it is properly seated on pulley.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Stamford, CT
- Parts Used:
- WH41X10096, WH1X2594, WH16X513, WH02X10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Changed drain hose on GE washing machine
I attached the Drain Hose Clip to the Drain Hose Extension and then pushed the drain hose all the way into the drain hole in the back of the machine. I then screwed the clip to the machine. Done. Very painless. Fast delivery... ordered it on Monday, arrived on Tuesday.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erick from Elmhurst, NY
- Parts Used:
- WR2X9391, WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Light switch inside refrigerator wasn't working
First turned off power and removed top shelf.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANNE from SWANNANOA, NC
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost Despenser Lid, Droped It And Havent Seen It Since.
Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Bel air, MD
- Parts Used:
- WH01X10302
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Washer drum would not spin, broken belt
I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jania from Novato, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigirator light would not come on.
Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennie from Louisville, GA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broken
Inserted handle into slots
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from WILLOW STREET, PA
- Parts Used:
- WH23X10043
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
would not empty the water
read about the problem ordered the part and then installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from Hagaman, NY
- Parts Used:
- WH01X10302
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
belt fits too tightly toget on easily
took two people to get this belt on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Midland, TX
- Parts Used:
- WE04X20089
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic Shaft Broke
My husband un-screwed a few screws to take the cover off then just rewired the new timer and put the cover back on. I actually had an easier experience with this website than the actual GE website, which I used prior to partselect, and ordered the wrong part. Thanks and I will definately refer and use this site again. AWESOME!!
Was this instruction helpful to you?
Thank you for voting!
replaced start button and start switch
disconnect power plug unscrew 3 screws in back. lean forward remove button disconnect 2 wires in back of switch. put switch connect 2 wires and button. connect 3 screws in the back. ready to start working
Was this instruction helpful to you?
Thank you for voting!