DBSR453GB1CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- joseph from no. attleboro, MA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob on dryer
pushed replacement knob on shaft of dryer. machine works better than new. took less than 24 hours from time of order to time of delivery to my house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shauna from Bend, OR
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
High Squeaking noise
I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gig Harbor, WA
- Parts Used:
- WE01X20580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old door handle broke off
Inserted replacement door handle into two slots on door and snapped into place. Amazingly easy and a perfect fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Wake Forest, NC
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer wouldn't start due to what I knew was a problem with starter knob/switch.
Very easy!! Took off front panel. Removed faulty starter knob/switch. Connected new switch. Reattached front panel. Started right up!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vlad from Durham, NC
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer wouldn't run at all
replaced the start switch, and it worked like new. took me only about 5 minutes to replace the switch. thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Middletown, NJ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Dryer Knob
Removed and replaced knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Johnson Valley, CA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new knob for my dryer
All I did was stick the knob on. How easy was that! Knob works every time. Very pleased with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KETURAH from KATY, TX
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Would Not Turn On
We ordered the part and I remember coming to this website and reading the reviews. So when my husband came home we pulled out the dryer and we unscrewed the back of the top plate. We then took the needle nose pliers totake the wire off which there are three of them just remember when changing the switch where the red wire goes instead of going uotop it goes on the bottom. After that we were done and I would say that it took about 15 minutes. When doing this make sure unplug the dryer before you do anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from St. Augustine, FL
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not start
With your drawings, we identified the part and my wife installed it by herself about 3 days after we ordered it. Great Service! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hector from Baytown, TX
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had Difficult Time Getting Dryer To Start When Turning Switch
Pop off top access panel twist switch out and reverse twist switch back in. . Very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Fresno, CA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not start
Unplugged the dryer. Removed the top hood with a phillips screwdriver. Twisted out the old starter. Unplugged the connectors on the starter (they were not in the same location as the new starter but were numbered so I kept the numbers consistent. Put the new starter in and plugged in the connectors. Plugged in the machine - hit the "on" button and viola! Easy cheesy lemon squeezy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Decherd, TN
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
start switch would not turn off
First dis connect from power sourse remove knob and the four screws that secure that instrument panel from machine.With a simple twist removed the defective switch,inserted new switch, transfered wires from old switch to new, replaced the panel and knob, reconnected power cord and it's done. Total time for this repair was less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Houston, TX
- Parts Used:
- WE01X20580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken handle
Snapped right on! No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Columbus, OH
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would turn-on intermittently
Replaced power switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Maryville, TN
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob
Used pliers to remove old clip. Installed new clip and knob. Very easy.
Was this instruction helpful to you?
Thank you for voting!