DWSR483EB0CC General Electric Dryer - Instructions

Hello,

I just want to start by saying thanks to Partselect for having such a great website. The site is easy to navigate and with the explosion views allowed 'us novice' to select the right part the first time.

With post from previous DIY'ers, help make my repair very easy and simple. I had to replace the timer and the Pulley Idler. I first removed the top, leaving the timer panel connected by wires. I then removed the belt from the drum. That step was easy since the Pulley Idler was broke. I simply slid off the drum with ease. Once the belt was off I disassembled the front panel of the dryer. With the front panel off, I used a 3ft clamp to hold the drum in place while I unscrewed the three drum screws inside. I then pulled the drum out and set to the side. The tension pulley was simple to remove and reinstall. I reversed the steps above until the I got to the installation of the timer panel. With the new timer I put them side by side. I pulled one wire at a time and replaced to the new timer. Once all wires have been transferred, I then pulled the knob off the front. I used a small and medium flat head screwdriver, the small one to pry up the keeper flap and the medium to hold it. I was able to turn the timer and release it with ease. I then inserted the new timer and replaced the knob. I finished reinstalling the dryer and tested. Works great! This all took approximately an hour.

Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

r/r parts unit runs great

i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.

I followed the great tips from the other repairs and that part was easy. Turned out not to be the exact problem. The problem was the rear bearing shaft which in another 20 min I had the drum out and repaired. Now the dryer is like new and will hopefully last another 5 yrs.
Thanks Parts Select for your help!

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

Your instructions were execellent
Problem is solve
Thank you

Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

snap in snap out

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal