DWSR483EB0CC General Electric Dryer - Instructions

Removed two screws, lifted the top, removed two more screws and tilted the front panel. The worn parts were accessible, and I simply placed the new parts in. It worked. A little trouble placing the top back in the slots, but a fist whack did the job.

I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.

followed the video you provided and it was easy!

if your unit has over 6,000 hours of operations, one needs to remove the front panel and inspect the sliders that the drum rides on. The video were very helpful to replace the sliders. Unfortunately, my dryer had over 10,000 hours of operations over a 30 years period, hence a major repair costing over $200.00 dollars. The drum sliders were gone, hence the drum eat through the plastic guides. More so, the drum started to eat away the front panel. If the dryer is eating your closes and making a noise, one is looking at a $200.00 repair job. Hence check the sliders early will save one $$$$.

Open the door and removed the part. Installed the new part and started the dryer.

At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push

Took new one out of package, and push it on. 4 seconds!

Just push knob on less than 4 seconds

handle broke on sunday( not the best day to order things). ordered it from this site and had it by tuesday. great service and best price i found on the web. tks

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

I was able to take off the front top panel (4 star screws) folded top panel towards me. Marked all the wires to make it easier to remember where they go on new timer. (could have just removed and replaced on new timer as wires were long enough. Pushed old timer down onto panel with screw driver to loosen (this was hardest part) once I was able to loosen and remove the new timer was easy to replace and tighten. Put wires in place. Folding top panel back into place. Closed and tightened screws. Project done!!! Saved about $200.00... GO ME!!!

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.

Hello,

I just want to start by saying thanks to Partselect for having such a great website. The site is easy to navigate and with the explosion views allowed 'us novice' to select the right part the first time.

With post from previous DIY'ers, help make my repair very easy and simple. I had to replace the timer and the Pulley Idler. I first removed the top, leaving the timer panel connected by wires. I then removed the belt from the drum. That step was easy since the Pulley Idler was broke. I simply slid off the drum with ease. Once the belt was off I disassembled the front panel of the dryer. With the front panel off, I used a 3ft clamp to hold the drum in place while I unscrewed the three drum screws inside. I then pulled the drum out and set to the side. The tension pulley was simple to remove and reinstall. I reversed the steps above until the I got to the installation of the timer panel. With the new timer I put them side by side. I pulled one wire at a time and replaced to the new timer. Once all wires have been transferred, I then pulled the knob off the front. I used a small and medium flat head screwdriver, the small one to pry up the keeper flap and the medium to hold it. I was able to turn the timer and release it with ease. I then inserted the new timer and replaced the knob. I finished reinstalling the dryer and tested. Works great! This all took approximately an hour.