DBL333EBC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Ennis, MT
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dryer start switch broken off
Put in the new switch and it starts great. Now that it runs there is no heat. I assume the elements are out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Wheaton, IL
- Parts Used:
- WE12X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The drum stopped turning in the dryer
Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Maryville, TN
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob
Used pliers to remove old clip. Installed new clip and knob. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Fernley, NV
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch was broken and had to use pliers to start dryer
Disconnected the power removed 4 screws from top panel. Removed 2 wires, turned switch counter clockwise. remopved switch. Replaced with new switch,connected the 2 wires, put panel back inplace,put screws back in panel,plugged dryer back in. SUPER SIMPLE Total time 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Valdosta, GA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The old knob hasd split and wouldn't turn the dryer on
I took the visegrip pliers off the d shaft and simply slid the new knob on with ease. I never doubted my abilities!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Middletown, NJ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Dryer Knob
Removed and replaced knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Sun City West, AZ
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Sticker Switch Worn Out
Simple replaced switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanie from Barlow, KY
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken start knob on dryer
old dryer knob had lost its spring and would not turn on. simply pulled old knob off and replaced by pushing new knob onto shaft. voila! saved myself a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Moyock, NC
- Parts Used:
- WH01X10060, WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch broke
Remove the top of dryer, remove switch after two wires removed. Snapped in new switch and hooked wires and then put top back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erin from Tucson, AZ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
The old knob broke off & was no longer able to turn the pin to start the dryer. I simply slid the new knob onto the pin & it worked like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from Destin, FL
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The knob broke
Took the knob and clip off the dryer and stuck the knew knob on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Johnson Valley, CA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new knob for my dryer
All I did was stick the knob on. How easy was that! Knob works every time. Very pleased with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENDALL from COCOA, FL
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inoperative Switch
Remove & rplace switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrienne from Beaver, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Start knob broke from being turned too far
Fortunately I watched the video on how to change the knob. I may not have noticed that the metal clip part of the old knob was still attached. Once the old part was removed, the new knob slid right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Staten Island, NY
- Parts Used:
- WE12X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the dryer belt broke
very simple my husband put it on in no time
Was this instruction helpful to you?
Thank you for voting!