DBL333EBC General Electric Dryer - Instructions

We are a retirement community and when we opened March '07 the company purchased GE washer and dryers to go in our common area laundry rooms for the residents to use. Because of their age, they will often turn the knob counter clockwise and not the right diirection which breaks the device which is not good. With in 3 days of installation they had broken 2 of the new knobs.
But, the ordering was simple, the shipment was fast and the install was quick for the maintenance tech.

Followed the on line instructions.

open the front of the dryer, open the back access panel, remove the old belt fragment, pull front cover away from bushing surface at the front of drum, drape new belt around the face of drum, match location visible as the track of old belt, reroute belt at the motor and install tensioner in the proper way, reattach front cover, install back panel, done.

Pulled the top of dryer off. Separated the door from the drum seal or gasket, slipped the belt through, put the drive belt on the motor and then put it all back together.

The repair was simple with my mechanic relative handling the tools. Total time about 25 minutes.

Previous repairs to the venerable machine with parts obtained freom Part Select and shipped to Germany: new drive motor and drum bearings.

Removed the top, front and lower rear section of the dryer. This being my first experience replacing a dryer belt I naturally missed the tensioner pulley first try, then installed the belt on the wrong side of the pulley and found I didn't have enough tension. After some thought and a long hard look I realized my mistake and the third time was the charm. Next time I need to replace a dryer belt it should be a snap and go a lot faster.

Unplugged machine and turned off the gas. Removed top panel,4 screws along inside top edge of door opening. Used a wooden shim to pry the drum away from the surrounding "lip with felt padding. Slipped belt through.the trick is getting the belto around the entire drum. First I got it over the top of the drum, and fed it around the bottom by turning the drum and pushing the belt through the opening made by the shim between the bottom of drum and the lip with felt. It was kind of like feeding a bicycle chain onto a sprocket as you turn the wheel..
Removed back panel and vent hose, removed old belt laying on floor of machine, fed the belt onto the motor pulley and the tension pulley. Tension pulley presses on top side of belt. Belt should be in same position on drum as old belt, you can see a friction mark all around the drum from the old belt.
Replaced panels and vent hose. Put felt padding back into place wherever it slipped out. Very important because if you don't it scrapes the drum when turned on and makes a loud sound.
Dryer works perfectly again.

unplugged dryer,removed air duct,,remove( top of dryer) by removing the two back screws.... removed two screws under (fornt top lid),laid top to the side. ...Now remove ( front of dryer) remove,two screws near the( top on the inside)...lean dryer back, and remove outsidescrews at the bottom)..the front should come off. ..located small square opening in the back of the dryer release clamp from drum ,...put belt around drum... put drum and dryer back together...(relace any electrical wires removed if any..remove (rear bottom plug panel)..you can now see the lower inside of dryer....make sure belt is level on drum by rotating...place belt on lower pully,... lift tension(spring pully) on to belt.. replace cover..

Removed the Drum and replaced the part....

I followed the video instructions. I did have to run to the hardware store to pick up a torx screwdriver but otherwise the instructions were perfect. I generally hire someone to do repairs, but this was too easy! I highly recommend doing this yourself as it is definitely a time and money saver. The website made ordering easy and the part arrived quickly!

Checked out problem found belt broke and order part from part select and when it got in I replaced the belt and then found pully bad too. so I order that part from ya'll and it tok less than 5 mint to install. everything went very well and I and my wife are very happy with everything.
Thank's Partselect,
John& Roxanna

Just push the new knob over the metal pin

pushed replacement knob on shaft of dryer. machine works better than new. took less than 24 hours from time of order to time of delivery to my house.

removed 4 scewws deom case snapped out switch placed the new one attached two wires re attached with the 4 screws

Removed old switch, replaced it with new