DWSR483GB1CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Plattsmouth, NE
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Load Noises when dryer was running
Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Fort Washington, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Squeeky Noise When Dryer Was Running
First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Peoria, IL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the dryer had a lovely squeak
I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from Winter Garden, FL
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic Start knob broke
Just push the new knob over the metal pin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from no. attleboro, MA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob on dryer
pushed replacement knob on shaft of dryer. machine works better than new. took less than 24 hours from time of order to time of delivery to my house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Johnson Valley, CA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new knob for my dryer
All I did was stick the knob on. How easy was that! Knob works every time. Very pleased with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Bristolville, OH
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screeching noise when drum went around
To get to where the drum slides go you have to first remove the dryer top. Then you have to remove the two screws that hold the dryer front/door. Found inside the dryer about an inch down on both sides. Be careful because it will fall off. Lower carefully as there is an electric hook-up on the bottom of the door. On the door top are the brackets that the slides slip into. My dryer has 4 slides. Sold individually for some reason. You are done except for re-assembly. Slip dryer drum back on door, press the front until you hear it click back together. Put screws back in and top back on. You are done and no more screeching!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KETURAH from KATY, TX
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Would Not Turn On
We ordered the part and I remember coming to this website and reading the reviews. So when my husband came home we pulled out the dryer and we unscrewed the back of the top plate. We then took the needle nose pliers totake the wire off which there are three of them just remember when changing the switch where the red wire goes instead of going uotop it goes on the bottom. After that we were done and I would say that it took about 15 minutes. When doing this make sure unplug the dryer before you do anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from St. Augustine, FL
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not start
With your drawings, we identified the part and my wife installed it by herself about 3 days after we ordered it. Great Service! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Houston, TX
- Parts Used:
- WE01X20580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken handle
Snapped right on! No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Fresno, CA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not start
Unplugged the dryer. Removed the top hood with a phillips screwdriver. Twisted out the old starter. Unplugged the connectors on the starter (they were not in the same location as the new starter but were numbered so I kept the numbers consistent. Put the new starter in and plugged in the connectors. Plugged in the machine - hit the "on" button and viola! Easy cheesy lemon squeezy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Decherd, TN
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
start switch would not turn off
First dis connect from power sourse remove knob and the four screws that secure that instrument panel from machine.With a simple twist removed the defective switch,inserted new switch, transfered wires from old switch to new, replaced the panel and knob, reconnected power cord and it's done. Total time for this repair was less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Wake Forest, NC
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer wouldn't start due to what I knew was a problem with starter knob/switch.
Very easy!! Took off front panel. Removed faulty starter knob/switch. Connected new switch. Reattached front panel. Started right up!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Columbus, OH
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would turn-on intermittently
Replaced power switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Maryville, TN
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob
Used pliers to remove old clip. Installed new clip and knob. Very easy.
Was this instruction helpful to you?
Thank you for voting!