DWSR483GB1CC General Electric Dryer - Instructions

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.

r/r parts unit runs great

i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa

I pulled the panel off of the dryer, screwed the part back on the correct wires, replaced the panel.

After reading a slew of scenarios that sounded exactly like my situation, I decided that the logical thing to do was give it a go myself. Everyone mentioned how simple it was--pop off the cover, remove wires, reconnect wires to new starter, and boom--up and running. A $22 part (that came VERY quickly) vs a min $100 repair person house call--and who knows if they would have taken me down that path we all know too well..."well, it's a complicated problem and will need blah, blah, blah, and $$$. Even my wife was impressed at how I "diagnosed" AND fixed the problem easy, quickly, and for a $22 part! Very pleased (with myself, too)!

Took top off ,4 screws.Took old timer out and just transferred wires to new one, very easy and worked perfect.Would probally get new knob also if ever done again.

Imagine that!! Move 3000 miles from home to home and after 90 days in storage, we finally get our things. First the washer, then the dryer. Test, no water, okay...Open valves. It's like magic. Hmmm. Plug the dryer in. No sound, not a peep. Turn the start switch one more time, crack-crack, the knob falls in my hand. Ordered the part and got in 2 days. A few star bolts to remove, unplug 3 wires and presto, it works like magic. Thanks!!!

Actualy finding the square bit driver was the hardest part of the ordeal.. After that simply removed back panel (3 Screws) removed the existing switch, removed the three wires that went to switch, reinstalled them on new switch, reinstalled new switch into housing and replaced bac panel. Couldnt get any easier! Total time 5 minutes. ...No Brainer!

Pulled front panel off, popped off the old switch, popped on the new switch. Good to go.

Pulled power plug. Removed the "Start/Stop knob" Removed 4 starbit screws across the top of the control panel. Flipped control panel down(toward front of dryer)to expose swithes. Aligned the new switch next to the switch being replaced, removed a wire and re-installed on the new switch. I did for each wire. To remove old switch, rotate counter-clockwise and lift out. Line up slots on new switch to panel slots, push down and rotate clockwise to lock in place. Re assemble panel, line up slot on switch knob to switch shaft and press on.

I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier

1. Unplugged dryer
2. Removed 6 phillips screws from back control panel
3. removed wires one at a time and installed on new switch
4. removed knob
5. lift lock lever and rotate switch ccw
6. installed new switch , rotate cw and be sure lock lever secures switch.
7. install back panel and knob

I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!

very simple , unplug dryer and unhook the back of the top of dryer using a screwdriver on 6 screws. unhook clip to the rotary starter switch and unhook the three pronged plugs that go to the starter switch. replace new one that snaps into place, plug back in the three wires. screw the back of the dryer back on and your done. 6 minute job that saves you 40-50+ dollars for a repair man plus the extra money they mark up the parts