DCCB330GDW General Electric Dryer - Instructions

I ordered the part via the internet. The shipping date was delayed twice but you excellent customer service department followed through and expedited the order. I installed it myself. Thank you.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

Open up the unit's lid first and then removed the front panel. Then I removed the broken belt and then routed the new belt around drum, through the belt tensioner, and onto to the motor pulley. I checked to make sure the belt was securely in place and if it would rotate the drum. Once I was positive it was in place I put the dryer panels back together, plug in the dryer, and tested operation. The only thing that was difficult was trying to figure out the routing of the belt through the tensioner because the old belt wasn't in place anymore. In all it was a 45 minute job.

As I pulled each of the 3 bolts, I put a alignment rod into each of the holes. After I pulled the old deflector off, I had basically 3 pins/rods to slip the new deflector on and keep everything in basic alignment. Pulled one rod, reinstalled the bolt, so on and so on. Ran motor for noises or misalignment and had neither. Pretty simple repair.

I removed the front cover and top of the dryer by removing screws visible from opening the dryer door. I then had to figure out exactly how the belt was set around the drum and other pulleys. With the belt around the drum and around the motor rotor, the other pulley had to be very forcibly pushed towards the drum in order to get the belt seated correctly. This being my first dryer repair, I was unsure of how the belt was needed to placed. But eventually figured it out using pictures from the internet. The second pulley required a lot of force and I had to squeeze my hand and arm under the drum of the dryer in order to make the belt fit correctly with enough slack to reach around the second pulley.

The dryer made a loud squeal and I shut it off immediately.
1 - Unplug the dryer
2 - Took the top off and the front off the dryer
3 - Removed the 4 Front Dryer Drum Slides that were worn all the way through
4 - Pulled the bunched up Felt
5 - Vacuumed out the inside of the dryer -Very Important
6 - Put the drum slides in and felt piece
7 - Put the front on top back on
8 - Worked great

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.

r/r parts unit runs great

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.

removed two phillips screws from front panel, removed front panel and raised top cover, had my wife hold up top cover while i removed belt and installed new one, reassembled in reverse order, turned on dryer and checked for proper operation, and yes i did unplug the unit. worked great!!

pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

The top and front of the dryer had to come off, and taking off the top (and later putting it back on) was the hardest part. The old seal was stretched approximately two feet longer than the replacement part, and its thinness caused the drum to squeak as it scraped by the door panel. We simply pressed the new seal into place after pulling out the old one. Piece of cake. Putting the front of the dryer back on was simple as well. Fitting the top back into its slots properly was the biggest pain of the whole ordeal. The part came in about 2 days. Thanks!