DDC0580NKL General Electric Dryer - Instructions

Removed the rear access panel (8 - 10 bolts), checked the pullys. Opened the dryer door, removed 4 allen screws at top and lifted the top of the dryer (like a hood on a car). Removed a screw (phillips) on each side (inside) pulled open the front and worked the belt around the drum. Placed belt onto pullys, plugged in checked for proper rotation of drum then unplugged and installed screws and bolts. - Fairly easy, saved a bunch from a service call. I also found 15+ years of lint inside the dryer. Vacumed and cleaned the inside -it even dries faster! Sorry Honey - No new dryer this year - Now can I go hunting?

snapped in new latch

After removing the front panel with a 1/4" nut driver; I removed the drum, rear shield and spacer using a 3/8" ratchet, 6" extension and torx socket for the three drum screws. I then removed the 4 screws on the rear heat guard panel to get to the rear bearing assembly. I removed the rear bearing assembly and replaced the plastic bearing and then re-assembled it. Total time was less than 30 minutes. Now the problems began. Trying to line up the drum to the bearing plate was very difficult due to the bulk of the drum. After some frustration time I devised a way to do it. I took 3 1/12 inch #10-24 screws and cut the heads off. Then I screwd them into to bearing plate as guide pins. I then backed them out after installing each of the mounting screws. It worked very well. Next as I have large arms and hands Iworked form at least 30 minutes to attached the drive belt to the moto and idler pulley. I finally got it on by attaching the belt first around the motor then pulled the idler arm down to engage it over the belt. Took a lot of positioning my hand correctly to get enough leverage to pull the idler arm down far enough. All in all not to complicated and my wife just won't part with this dryer that really dries clothes quickly.I glad I took on the task to repair it and my hats go off to PartSelect.com for quickly and correctly filg mypart order. Hope you have the same success.

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

I removed the old lint filter and put the new one in! Grateful to find this item for my "antique" dryer.

removed cabinet
removed drum
dismanteled blower assy
found a tooth brush in the assy.
replace blower wheel
checked timer and heating elements
reassembeled
advised my wife of the problem

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

Just changed lint trap by removing old one and replacing new one.

Simple - took out the defective filter and replaced with the purchased part. The hardest part was figuring out the right lint filter. The extensive info on PART SELECT was very helpful.

I removed the rear panel to access the drive belt. Lowered the pulley to remove the belt and then took off the front panel and popped the top lid off. The belt was slightly frayed on the edges and looked a little old. Inside of the dryer was filled with lint, noticed the vent that sucks the lint from the dryer was almost totally blocked because off caked on lint. Probably from the moisture when we lived in Tx and had it in our garage. Sucked it out with the shop vac and scraped the rest. Removed the whole drum and that's when I noticed the rear drum bearing was totally destroyed and only a piece or two remained. Ordered the drum bearing and drive belt. I was about to put them on when I saw the drum slides were worn pretty thin. So I had to order more drum slides. That's why it took me so long to repair the dryer. If I had the parts already, it would have only taken an hour or so. I was pretty excited that I did it myself, since my husband usually fixes everything around the house. Easier than I thought :o)

first I removed the screws with the nutdriver at the bottom of the dryer at the back..then I could see the belt was broken...next I took off the 2 nuts at the back that hold the top on ..then opened the dryer front door and unscrewd the 4 screws holding the top on....then I lifted the top up and to the side...then all I had to do was take out 2 screws one on each side of dryer front and the the front was open enough that I could slide the new belt on dryer..then screwed the front back on...then placed the top on and went to the back of dryer and put belt on pulley using the diagram I found in the instructions inside the dryer top...really a lot easier than it sounds...easy fix saved me from buying another dryer

After opening the front door there are screws that are holding the top to the door. Take those screws out using a Phillips screwdriver. The top should lift up and rest at a near 90 degree angle.

The door has two screws at the bottom that need to be taken out. Once those are out there are two screws on both sides at the top holding it to the frame. Remove those as well.

Before you remove the front you should document the wiring for the door light switch. I took these off to give the door a little extra room so I could rest it on a toolbox without taking all the wires completely off.

Once the door is free, on the back there is a metal plate with two screws in it roughly in the middle of the unit. Unscrew the top completely but leave the bottom screw in and just slightly loosen it. This will allow it to swing down out of the way without the need to completely remove it and have one more part to put back together in the end.

What this plate is covering is the center of the drum. There is a small metal tab that you can push on and it will push the drum out so it can be removed. Gripping the drum, you can lift it out by guiding it through the notches on each side where the drum protrudes.

With the drum removed you'll see the motor and idle pulley. On my model the pulley was attached to a metal rod that was spring loaded. The pulley is held on by a small tension washer that was easily removed with pliers. Installation was somewhat more difficult but mostly just getting it lined up and started. Once on the rod it was easy to push it into place.

With the new pulley installed it's time to install the new belt. To do this first put the belt over the drop and then replace the drum back into the frame. Once the drum is pushed back into the hole it will support itself.

Now you need to remove the panel on the back to get access to the motor and pulley. This panel has a lot of screws. Once that's off you can then guide the belt over the motor and get the idle pulley to put tension on the belt.

Once that is complete just replace all the screws you removed, plug it back in and watch as your new belt moves the drum once again.

Took to many parts off to find out only needed to remove four front screws under the lid. I lifted the lid and found the thermostat and replaced same dryer now works great again at normal temps.

I discovered that the High Limit Thermo was in place, but had been bypassed years ago. After lifting the top up, I finally found the HLT on the top left side in the back. I removed it, then put the new one in with its 2 screws. I put new lugs on its wires and put them back on. The dryer tested GOOD. No more potential Bar-B-Que! I did print a picture of the wiring diagrams that were on the back of the unit. This gave me the color code of the wires, where they were to be found, and what they did. This also helped. This GE Dryer is at least 26 years old! Newer Dryers in the Videos actually require more work removing things to get to the Thermostat. When I finally found it, the job went quick.

I removed the front panel and the top of the dryer, pulled the drum forward and removed the old rear drum bearing then inserted the new rear drum bearing. I didn't replace the washers or the retaining ring in the back. Put the drum shaft into the new rear drum bearing. Put the front panel and the top in place and started using the dryer again.