UAN7214C Frigidaire Dryer - Instructions

Have done this before - dissembled, cleaned everything, re-assembled with new parts - rear bearing, idler, and belt. Hardest part is getting the spring back on the idler pulley.
You take the top lid off, remove the front panel and then the drum. remove the access panel on the back to release the spring tension on the idler pulley, then remove the drum. Vacuum clean everything, then reassemble with new stem and bearing, new belt, and idler pulley. Test spin drum by hand - if belt comes off it's likely twisted. Put belt back on and try again. Try operating with air mode to spin drum. If belt stays on, complete re-assembling and make sure you have no screws left over!

Popped the top of the dryer off. Removed 3 screws from lower front panel. Removed front panel slide belt over drum, remove 2 bolts from rear panel and installed belt over motor and around idler tensioner. Reinstalled front panel and top of dryer . Also greased idler pulley to shaft , beings tensioner was okay. Plugged in and tested dryer, it was okay.
We went to PartSelect. com and order the belt and it was fast shipping. We couldn't find the belt anywhere else. Thanks for PartSelect.

I first removed a vent cover in the back where the idler is located. With pliers I removed the tension off the spring. Next I simply slide the idler off the post. I pulled up on the top panel which opened like a clam shell. I used a flat blade screw driver to separate the front panel from the dryer so I could slide the new belt around the drum. I reversed the steps. All in all it was easy. It took me about 30min including cleanup.

Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.

unscrewed old screen, installed new screen assembly.

1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

I took the front part off, then removed the old belt out and installed the new one in. Also fix the tensioner wheel (it had come off) After I posisoned / aligned the belt. Also cleaned the whole dryer with compressed air, it was really dirty and nasty, this dryer has not been cleaned in 20 years, overall I had a great experience with parts select, they send the parts real fast.

Tank you

Jorge Garcia, Buena park CA

I raised up the top then took 4 bolts out of the front and it came off and then I slipped the belt on. Now was the fun part. I tried to put belt around the tension spring from the front of the machine. Bad mistake. So I turned the machine around and took off little plate bottom left, back side reached in and WA-LA back in commision. I took a long brush and cleaned all I could reach and put it back together. Bingo, back in business.
And I'm 71 yrs. old.

I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

First I unplugged the dryer. Then I gently pryed the top of the dryer. This was done from the front using a flat screw driver. Do this gently pushing up on the handle of the tool. It will pop up one side at a time. No need to remove the screws and clips on the the rear top of the dryer. Set the top aside. Then from the inside front of the dryer using a phillips screw driver I removed two screws, one on each side. This allowed me to lift the front of the dryer up and away from the unit, off the two clips on the bottom front of the unit. I set the front cover on top of the dryer. There is no need to disconnect any wires. Next removed the rear vented cover on the back of the dryer so I could acess the belt pullies. From here I pushed the upper left pully to the right to ease belt tension and take the belt off that pully. Slide the belt to the rear of the drum. Next I removed the three screws from the center most part of the inside of the dryer drum. My dryer required the use of a square head driver tool. This allowed me to easily bring the dryer drum out the front of the unit. Set it out of your way. Then I vacuumed the dust out of the dryer. Then I lifted out the metal part that resembles a trailer hitch which had been attached to the dryer drum. Next using a nut driver I removed the two screws which hold the white plastic part of the bearing assembly to the rear of the dryer. That is all the taking apart work.
Putting it all back together was not too difficult. First install the new white plastic part of the bearing assmbly inside the dryer along with the metal part on the outside rear. The little metal ball bearing goes on the OUTSIDE between the little metal part and the rear wall of the dryer. Do not leave it out as it provides electrical grounding between the dryer drum and the body of the dryer. Next attach the new bearing part that looks like a trailer hitch to the rear of the dryer drum. This is the three screw part. Then lift the drum back into the dryer. Do not yet set the drum all the way in. The dryer belt must be looped around the drum. I installed a new belt. If the bearing is worn out it is time for a new belt. The smooth side of the belt goes against the dryer drum. Now apply a generous amout of lubricant to the white plastic cradle which was installed on the back of the dryer and to the ball bearing area. Then the dryer drum may be set into place, that is the trailer hitch part into the white plastic cradle. Now the front of the dryer may be reinstalled. Push up on the inside of the dryer drum to line everything back up. Put the two screws back which hold the dryer front on. Be carefull not to drop them inside. Put the dryer belt back into place on its pullies. It goes on the inside of the left and right pullies and on the outside (bottom) of the pully of the dryer motor. Check for and undo any twists. Plug in and test the dryer. All should be well. Reinstall the rear vented cover. Replace the top, connecting the rear first. Make sure to reattach the green grounding wire. Then push the front of the top down onto its clips. You are done! This took me 1 hour and 10 minutes. It sounds like alot but you can do it! Empower yourself!

lacked instructions. Internet yielded a simple paragraph. Scored real bonus when we discovered the lint build up past the internal filter was approaching catastropic level. Replaced the exhaust tube (plastic) with rigid metal and resolved to disassemble and clean dryer on 2 year cycle in future. Kit just isn't complete without detailed instructions. Parts were complete and sufficient. Local codes have eliminated the plactic exhaust tube. Recommend that all old installs refit to rigid or semirigid before the fire happens!

First removed the top of the dryer, then the front of the dryer. Took the plate off the back left of the dryer to disengage the belt off the pulley.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.

Opened the top, removed the 4 screws that held the front top the cabinet, took the front off, went after the dust with the vacuum cleaner, lifted the drum, installed the belt, put the front back on, and put the belt over the idler. Most of the time was in the cleaning.

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you

Just like in the video, but with a stackable washer/dryer unit, works like new now....