7348A Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carol from Gilbert, AZ
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint screen was torn
It took me all of 1 minute to take out the old lint screen and drop the new one back in.!!! I didn't need the frame. I had no idea that I could find a replacement so fast!!! Just wish I had not waited a month to look for one. Thanks for the fast service ! !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hope from Sanborn, IA
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
torn lint screen
It was extrememly easy, just pulled out the old screen and dropped in the new one. I didn't use the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mrs. Frances from Oklahoma City, OK
- Parts Used:
- 131390300
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Just a lint screen (which I had replaced once before) but the local parts store wanted more than twice what this cost.
Easy, lint trap in front, unscrewed the old base, threw out the old lint screen which was hanging by a thread, and put the new (and - KEY WORD - cheaper) part in. All by Myswlf!
Thanks.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Seminole, FL
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Lint Screen had come apart
Changed the old one for the new, But the best part was the fast service getting the part. I couldn't believe that I ordered it and three days later it was delivered. Good Job!!!! I will recommend you to everyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from East Meadow, NY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Damaged lint screen
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christiaan from Saint Charles, MN
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Screen was becoming loose from its frame
No need to replace frame, just took the old screen out and slide the knew one in. About in two seconds its done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Canton, MI
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Torn Lint Screen
Replaced new Lint Screen. Changed Frame with two phillips screws. Total time spent: 3 minutes. Two day delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from rembert, SC
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lint screen was torn and badly bent and I could not find one locally.
Simply removed the two screws that hold the frame in place, removed the damaged parts, wiped down the surface area where the new one would mount and installed the new frame and screen in the reverse order from removal. SIMPLE and fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Piscataway, NJ
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Dryer
I did not think anyone would even carry the lint screen and frame for our OLD dryer. The price was reasonable and shipping was fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Loveland, CO
- Parts Used:
- 5303281153, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Bearing Was Very Noisy
Excellent!!! The parts fit perfectly, but most of all was the video that went through the repair step-by-step.
A local repairman quoted $198 for parts and another $150 for labor. Got the parts here for less that $26!!!!
The only issue (very minor) was the video called for a phillips head screwdriver to remove the front panel, and our dryer needed a squarehead driver. (If I was younger, I would have been able to see the problem).
But, I highly recommend Partselect!!!!
A local repairman quoted $198 for parts and another $150 for labor. Got the parts here for less that $26!!!!
The only issue (very minor) was the video called for a phillips head screwdriver to remove the front panel, and our dryer needed a squarehead driver. (If I was younger, I would have been able to see the problem).
But, I highly recommend Partselect!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Bells, TN
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Loud squeeling noise
I had trouble with the little piece on the back side of the dryer not lining up with the bearing housing. I also didn't see how the drum was gonna stay in place but finally realized the front cover lines it up. All in all it was awesome to get the part I needed so quickly and cheap, thanks a lot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Berkeley, CA
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Loud, piercing screeching from dryer
I followed others instructions on this site to disassemble but felt confident since 2-3 years prior I had replaced the felt top/bottom guides around the drum and the drum belt. The video on this page is also helpful
1) Pop the top with a putty knife
2) Unscrew two screws that hold the front onto the dryer frame
3) Lift front from two clips at bottom of dryer
4) Release tension from belt (unscrew/remove rear access plate)
4) Lift drum up and forward out of dryer
5) Unscrew drum bearing 3x screws from inside of drum
5) Remove the drum bearing holder
6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes.
7) Attach drum bearing
8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup)
9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place
10) Reverse steps to assemble
I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!
Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.
1) Pop the top with a putty knife
2) Unscrew two screws that hold the front onto the dryer frame
3) Lift front from two clips at bottom of dryer
4) Release tension from belt (unscrew/remove rear access plate)
4) Lift drum up and forward out of dryer
5) Unscrew drum bearing 3x screws from inside of drum
5) Remove the drum bearing holder
6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes.
7) Attach drum bearing
8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup)
9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place
10) Reverse steps to assemble
I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!
Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gland from Mount Pocono, PA
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The dryer squealed when operating.
I have a frigidaire dryer about 5 years old.
I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.
Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.
The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.
After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.
I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.
Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.
The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.
After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from seattle, WA
- Parts Used:
- 5303281154, 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Dryer had loud screeching noise
Followed the video on partselect web page.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kurt from Fargo, ND
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Loud sqweeking after dryer was in operation for over an hour
FOLLOW THE VIDEO!! I was scared to even get into it until I watched the video. Made it easy for me and I have little to no mechanicl skill. Excellent video that made it super easy. Took me an hour as I was taking my time. Now I could probably do the same repair in 20 minutes.
Was this instruction helpful to you?
Thank you for voting!