7348A Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gale from Portland, OR
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud squealing
Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Cottonwood, CA
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
squeek in rear bearing
There are really good instructions with photos on line - search squeeky dryer. I would add that it is easier if you mount the new bearing assembly on the drum before placing the drum back in the dryer cabinet. I guess this is obvious but was not stated in the referenced instructions. The round bearing slotts fairly easily into the plastic pillow block mounted on the back of the cabinet. Just make sure the small ball bearing remains in the center groove - lots of greese will help this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Mauston, WI
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud squeeking when ran
Followed online video. All went smooth. Runs great!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Clio, MI
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed new lint filter
took out two screw took out old lint filter put in new lint filter than I put back in the screws All done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from omro, WI
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lint sreen started to fray
Quick and easy job, took 2 screws out from old frame and removed frame and lint screen. Really only needed lint screen as old frame in good shape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from SAN ANTONIO, TX
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screen filter damaged
took out two screws and removed old screen,relaced with new screen,and replaced two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David Jacobson from Coconut Creek, FL
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Screen ripped and shredded. Caused painful cleaning of lint.
Perfect match for part we needed. Popped out old, popped in new. Works like a charm :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Hudson, NH
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bearings Went and Idler Roller fell apart, not allowing drum to turn
unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AL from roslyn, NY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lint Filter was Torn
Removed old frame and filter. Slipped in the new frame and screwed it in. inserted the new lint filter.
Done in under 5 minutes.
Done in under 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Two Rivers, WI
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screen was torn
Removed two screws. Removed screen frame. Cleaned lint from ductwork. Inserted new screen frame and replaced screws. Done in 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kunal from San Jose, CA
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original filter mesh was damaged and broken
All made simple by partselect.com as I was able to identify the part, and the delivery was quick and efficient. Rest was simple, removed two screws and the old filter mesh and put in the new one. It was done in less then 3-4 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Columbus, OH
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
accidently threw lint screen away
just place lint screen in dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from La Crosse, WI
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dryer lint screen had a hole.
Pulled out old screen (exactly like what you do to empty it), put in new one....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Whitesboro, NY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old screen ripped
2 screws (Philips) old one out, new one in, real easy..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Lexington, KY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the lint screen was old and holey. lint was getting into the dryer hose.
All I had to do was take out two screws that held the lint screen frame into the dryer, vacuum the opening to get the lint out that had accumulated, place the new frame in the opening, tighten the two screws that hold it in place, insert the lint screen and it was done.
Was this instruction helpful to you?
Thank you for voting!