FDE747RES0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from HGHLNDS RANCH, CO
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
load squeal
replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arne from Nome, AK
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rusty streaks on clothes.
I First pulled the top panel up and off from the front. Then, on the inside, removed a square head screw from each side holding the front door panel on. I then pulled off the front panel enough to expose the drum. I then removed the old drum glide with a putty knife, and following instructions supplied with the new glide, glued the new glide into place. I then assembled in reverse order of disassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- toshio from canton, GA
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was burning clothes
There was a gap between the drum and the front opening. So, we opened the top of the dryer using the putty knife. There are two clips once you find them you just have to push back on them to release the top of the dryer. Then there are two screws that hold the front of the dryer on. Once they are removed the front of the dryer just came off. The kit has glue and instructions past that point and I just followed them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Smyrna, TN
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer leaving brown spots on clothes
First I raised the top of dryer, then removed 2 screws holding the front of dryer to the sides. removed old drum glide using a putty knife and glued new glide in place with glue provided. replaced front and top. The whole job took about 20 minuets and saved me the cost of new dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PEDRO from BRONX, NY
- Parts Used:
- 131967600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the fan broke in half
i used one screw driver universal to pop off the cover then, i unscrewed the 2 screws off one on the left side and one on the right side, then useing the screw driver i popped off the left and right off the dryer houseing body their are 2 wires 2 unplug then at the back of the dryer theirs a vent 4 screw take then off then take off the belt then on screw the drum from in side pull out the drum,then 2 more wires to unplug now take off the blower housing with the motor and unscrewed the fan then your done. put it back the same way 15 to 30 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan from Dallas, TX
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The clothes was getting stuck on the tumbler
First I removed the 2 screws on the back. These 2 screws hold the top cover. I also used a flat screw driver to press the 2 locks that hold the top cover, they are located in front and under the top cover . Then I removed the 2 screws that hold the front cover. After removing the front cover I replaced the drum glider and the seal-basket lower. Now my dryer is working perfectly...
Was this instruction helpful to you?
Thank you for voting!
dryer was squealing loadly
took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Yucca Valley, CA
- Parts Used:
- 134398500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken switch
Removed rear cover, unplug 2 spade connectors, twist out old switch, twistin new switch. plug connectors, install cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Verlin from Hampton, IA
- Parts Used:
- 5303281153, 131553800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drum On The Dryer Quit Turning
1) I took a screw driver and pop the top lid up. 2) Took a philp screw driver and took 2 screws out of both sides of the front panal. 3) Lift up on the front panal and turned it out to the side. 4)Put the belt over the drum and on to the motor and tension pulley. 5) Put everything back together in reverse order starting with 3 ,2 and 1
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth C. from Fort Valley, GA
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clothes getting stuck in dryercausing brown stains on clothes
Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kymd from Campobello, SC
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The timer knob broke
Opened the plastic bag, took out the new knob, slid it on and DONE I'm not using pliers anymore!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emma from Omaha, NE
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob on dryer broke so it wouldn't turn the timer on
I know that the knobs on the Gibson dryers break as they are plastic and the back cracks so it won't turn. I have had to get several new ones over the years. I went to Google put in Gibson dryer knob and found it, I had the model number so that helped. I had the part within 24 hrs, awesome service from PartSelect.
Emma W
Emma W
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD from EDISON, NJ
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our Clothes Would Get Caught In Between The Drum & The Front Cover, Making Marks On The Clothes.
I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina from Richmond, KY
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer Knob broke off
Sooooo Easy. A no brainer. Just line up the knob and push it back on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARRY from HARRISBURG, PA
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob broke on the dryer
Pushed the new timer knob on the dryer. No tools were necessary.
Was this instruction helpful to you?
Thank you for voting!