GSGQ642DS0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Phillip from Marysville, WA
- Parts Used:
- 131873500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke
Pulled off the old knob, pushed on the new knob. It was that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NAPHTALI from PALO ALTO, CA
- Parts Used:
- 131873500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob broke
snapped on new knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from Thornton, CO
- Parts Used:
- 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
loud squeeling noise
After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Fort Worth, TX
- Parts Used:
- 5303937183, 5303937182, 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
dryer would turn for about 1min then stop
I replaced the rear bearing assy. Thanks to all that sent in there stories. very helpful. But my problem was the breaker in breaker box. needless to say "check your outlet for proper voltage.First,before anything else." i had a bad breaker, had it replaced,with proper 30amp fuses.Dryer works fantastic..Thanks to all again for your input. Great Website...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from OWINGS MILLS, MD
- Parts Used:
- 5303937183, 5303937182
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Noisy dryer
Followed instructions for removal and installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from New Roads, LA
- Parts Used:
- 131825900, 5303281153, 131724301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bearing bad and shaft broken
replaced bearing and shaft new belt and everything works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from hackettstown, NJ
- Parts Used:
- 5303937182, 5303281153, 137513300, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Very loud squeaking
Opened top, removed front cover, removed belt, took out drum, replaced bearing on drum and bearing guide on back of dryer. Reinstalled drum and belt, then replaced drum glides and upper felt,let glue set with clamps over night.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from Middletown, NY
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Tumbler not moving
Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- April from CARYVILLE, TN
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy
Took it apart and installed the parts. Then I threw the dryer in the trash and bought a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from SHERIDAN, CA
- Parts Used:
- 137513300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Glide was broken
I watched the video on the repair and followed it. Super easy. Repair only took 30 mins. Please note there are 2 glides. Make sure to order 2.
Was this instruction helpful to you?
Thank you for voting!
dryer was squealing loadly
took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer
Was this instruction helpful to you?
Thank you for voting!
Original drum belt broke
Watched the online video that showed how to replace the part. Was very easy to follow, but also I did open the inspection plate on the back to make it easier to put the belt on also to make sure that the spring and everything else look okay. As for the door switch took a photo with my phone of how the wires went on remove the wires, popped the old switch out put the new one in put the wires right back up the same way in my photo works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from ROYALTON, MN
- Parts Used:
- 5303937182, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
dryer had vibration after couple minutes of running
i read reviews and finally found a person that replace the motor, rear bearing, front top glides, and tension arm/pulley.. i had cleaned the fan motor with a tooth brush best i could the 1 time i had it apart. after the 4th time apart and reading a different review that said replace the fan motor housing/fan. i did and noise gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from HGHLNDS RANCH, CO
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
load squeal
replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from UXBRIDGE, MA
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken belt
Watched video sent to me after I purchased belt on line. Super helpful!
Was this instruction helpful to you?
Thank you for voting!