GSGQ642DS0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- charles from saylorsburg, PA
- Parts Used:
- 134042800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacing a function knob on the dryer
The knob split by the shaft. Quick and easy I ordered the exact part from Part-Select, it in 2 days and pushed on the new knob with my fingers.
It was quite easy thanks to Part-Select. You can be sure I will use them again!
It was quite easy thanks to Part-Select. You can be sure I will use them again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Emporia, KS
- Parts Used:
- 137513300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Front drum guidesnubber ring was worn out
removed the top of dryer, pulled front panel back from drum and installed snubber(Front Drum guide).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Fairfield, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heat would initially come on then go off or sometimes not come on at all.
1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara J. from Lancaster, CA
- Parts Used:
- 131450300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter was wearing out.
Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corey from Lodi, WI
- Parts Used:
- 131873500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced broken timer knob
Just pressed the knob on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Milwaukee, WI
- Parts Used:
- 131873500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
It was very easy, looked and found the right match and pulled off the broken one and pushed on the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Mentor, OH
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke and came off.
Simply popped it back into place, careful not to break the new handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharron from Portland, OR
- Parts Used:
- 131873500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
Took it out of the bag and put it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from Logan, UT
- Parts Used:
- 131873500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob was cracked
Just put on the new knob! Supper easy and it works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelia from Elizabethtown, IL
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
replaced broken belt
Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!
Was this instruction helpful to you?
Thank you for voting!
Broken knob switch
Took top off dryer which made easy access to switch and change part ,put it back together thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cherry from WATERVLIET, NY
- Parts Used:
- 134503600, 5303281153, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Very noisy
Replaced rear drum bearing, drum support bearing & drum belt. Still very noisy. Will order new motor & see if that does the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denis from LONGMEADOW, MA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas dryer would generate heat at the beginning of the cycle but would stop after 5 min and would start making a buzzing noise.
Unplug from electric outlet. Use putty knife to press on two brackets holding the top cover. Raise top cover. Unscrew two screws holding the front panel. Raise front panel up and move to the right (careful with the wires). Disconnect wires from coils. Unscrew two screws holding a small bracket holding the coils. Replace coils and reassemble everything. (HINT: make sure you drum is empty. Mine contained dump clothes, and it turned out front panel actually provides support to the drum, so mine was hanging there with some weight in it - probably not good).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Petaluma, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Gas dryer wouldn't stay hot.
I definitely would not have tried to do this had it not been for the other testimonials written here. But it sounded so easy, I had to just try it (the repair man estimated that with parts and labor, we would be looking at somewhere between $250 and $300!).
The repair itself took less than 15 min, but I spend a good deal of time looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.
It works!!!
The repair itself took less than 15 min, but I spend a good deal of time looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.
It works!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TJ from SCOTT DEPOT, WV
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this instruction helpful to you?
Thank you for voting!