FRQG7000LW0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edwin from Brooklyn, NY
- Parts Used:
- 5303931775
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no heat
Remove top cover 2 screws then remove front panel 6 screws remove wire connecter on the door panel. ignition coil is on the bottom left side need a short hand srew driver remove 2 screws remove plate holding coils remove coils and connecter. Reinstall in reverse installation. Dryer still didnt heat up so back to the drawing board :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Story City, IA
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Poly carbonite door handle snapped
Remove two phillips head screws on the inside of the door, fit the new part and reused the screws to attatch it. Careful not to overtighten the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from simi valley, CA
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replaced broken door washer handle. second incident
removed both screws. positioned handle. inserted the screws. tighten with screw driver done within two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Lolo, MT
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle cracked.
Rather than call repair co. and pay at least $100 plus parts, i decided to order parts myself. It came in less than a week. Watched the video on website. Did the repair by removing old handle with phillips head screw driver and installing new. Took about 5 min. I am a 72 tear old woman. Thanks for being online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Nantucket, MA
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The plastic handle broke off
There was video but all you do is unscrew the old screws and line up the handle and screw them in..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from Tampa, FL
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I shut the door too hard, and the old latch fell down into the inside of the dryer.
The new latch easily snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from valley springs, CA
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
front loading washing machine.
This is th esecond handle I have installed on this washing machine. The model number has disappeared from the label from being exposed to detergent and age. This web site provided EXCELLENT guides to ensure the correct part was ordered. The picture perfectly matched my handle. The part arrived VERY quickly and with EXCELLENT packing to ensure the plastic part was not damaged. The installation required two minutes to remove the damaged handle and install the new handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Balsam Lake, WI
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer wouldn't heat
Removed the panel between the dryer and washer. The gas valve was right in front. The wires were in a plug and easy to remove from old part. The solinoid held in place by a clamp with two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Pismo Beach, CA
- Parts Used:
- 134412860
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken washer handle
put the new handle in place on door and screw it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Essexville, MI
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer ran, had no heat
Your website was very helpful in narrowing down and diaganosing the problem. A continuity tester verified an open solenoid. Ordered Sunday evening, parts arrived Tuesday. Ignition coils drop in place with a holddown bracket and one screw. Wiring harness is reattached. Front of dryer is put in place followed by the top. Plugged in the dryer (it is just commom sense to have the power off). Started dryer, of course it ran WITH heat. The end of the story is HAPPY WIFE, HAPPY LIFE. Happy to do business with you. Tom , MI
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from Oak Park, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer would heat up but shut off too early
pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Darlington, SC
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke
Took screws out back of door handle.put new door handle up and put screws back in.it was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond Frattone from Richboro, PA
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not close because of broken female latch.
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from San Diego, CA
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
I had broken the handle while opening the door
Talk about super simple. Just open the dryer door, locate the two Phillips head screws holding the broken piece, undo them and you may have to hold the broken piece with a pair of pliers to get the screw out. Place the new handle in the appropriate position and re-install the two screws. Done....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Gibsonia, PA
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle broke at where screw holds it to the door
really bad design on the door, door breaks when pull is slightly upwards and washer is on the bottom of washer dryer stack so pull is always up.this is my third one. remove two screws and replace . takes about 2/3 minutes
Was this instruction helpful to you?
Thank you for voting!