FRQG7000LW0 Frigidaire Dryer - Instructions

arrived in 2 days. Using this company the replacement part cost me 75% less than the manufactures part, and it fits perfectly. It has a Slightly different color, but the price difference was huge. It was Very easy to install in only 2 minutes with a phillips screwdriver using the 2 screws provided. The manufaturer's part was $80 plus $11.00 shipping. This part cost me $25 with shipping. Amazing!

Two screws to remove the handle and replace with new one

Very simple. Just remove the broken door handle by unscrewing two screws from inside washer door. Replace with the new door handle.

I tested continuity on parts like burner (ok) then on solenoids (not ok) timer (ok) I visited several websites and found the AppliancePartsPros.com site with FREE repair forum and found valuable advice. Then ordered my parts at Parts Select and were delivered 3 later at my front door.
Now a days you almost can forget to work on all the electronics in a wasmachine and dryer, unless you're a electronic guru.
THks.

I took the old piece off and put the new one on very easy

I simply removed old handle by taking out the 2 screws from back of door and then replacing them into new handle . Repair man quoted me 50 dollars plus cost of part ,which was much higher than Part select price . The itemized drawings on the website are wonderful making it easy to order correct part first time .

Simple: Just removed 2 phillips screws, threw the broken handle in the trash, & put the new one on with the 2 screws. Problem solved.

parts arrive just like they said they would .had parts installed with in 15 minutes was drying clothes thank you your advice was perfect.

Popped the top... disconnected wiring... dropped the front... replaced coils... reversed sequence... done deal. No hassle, no worries, easy as 1-2-3!

Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.

Followed instructions and the repair went very smooth from start to finish. From getting tools out of tool tray to putting them back it took 15 minutes.

There was a small plate and 2 screws holding the 2 coils. I just removed the screws, unplugged the 2 coils, plugged the new ones in and put the dryer back together.

It is very very simple. All you have to do is remove two screws on the inner side of the door and the handle will pop right off. Then put the new handle in its place, and put those two screws back where you took them from, and now it is good as new!!

After reading other peoples problems i decided it must be the coils after looking at the picture of the part I looked at the dryer to find were the part was. it was right in front behind the inspection cover. so i order the part. it came very fast.these are not the first parts i have purchased from Partselect.the web site is newer now and i am glad because reading other peoples problems help me decide what was wrong with mine.PS Always clean every thing inside the dryer!! 15-20 min job one screw driver! (19 year old unit works fine)thanks to Partselect!!!

My dryer was heating up very briefly blowing hot air initially then cool. I have a stacking washer/dryer set (2002). I initially turned off the gas valve at the wall, ran the dry for several minutes to clear the gas line, then unplugged the power. I was then able to pop the top using a flathead screw driver, securely prop it open, unhook the wiring harness to the front panel, unscrew the two front panel screws, and remove the entire front without having to unstack the units. From there, you remove the two screws holding the bracket over the coils (2 of them), remove the electrical connectors attached to both coils and replaced them with the new ones. I then replaced all brackets, screws, and such (you'll need to lift the drum when putting the front back on and make sure it is lined up), plugged it back into power and turned on the gas to test the unit which worked perfectly. The 62% of the time seems to be an accurate figure as nothing else had to be done to the unit. Pretty easy stuff...good luck.