FASG7074LR0 Frigidaire Dryer - Instructions

I purchase one tube of heat resistant adhesive but I change both seals if you could afford to buy a second to I would recommend you do so the one tube just made it. For instructions on how to prepare the drum for installing new seals I went on YouTube

I seen a post on your website referring to the exact problem I was having. One of your staff recommended changing the control thermistor, which I did following the U-Tube video link you supplied. The repair went well and the dryer now operates perfectly ! Thanks for the accurate and helpful info.

Removed burner, unpluged 2 plugs on coils. Removed 2 screws, replaced coils, pluged 2 plugs to coils replaced 2 screws. Reinstaled burner. Dryer works great.

Unplugged the electricity, turned off the gas, then pop open the top of the dryer. Removed the two screws and pulled the front of the dryer off. Removed the two screws that locked down the two m series ignition coils. Put it back together and all things worked great.

I tested continuity on parts like burner (ok) then on solenoids (not ok) timer (ok) I visited several websites and found the AppliancePartsPros.com site with FREE repair forum and found valuable advice. Then ordered my parts at Parts Select and were delivered 3 later at my front door.
Now a days you almost can forget to work on all the electronics in a wasmachine and dryer, unless you're a electronic guru.
THks.

parts arrive just like they said they would .had parts installed with in 15 minutes was drying clothes thank you your advice was perfect.

Fast and easy. Started by pulling out refrigerator and unplugging it. Water valve for ice maker was already turned off due to leaking. Disconnected old valve, detached old valve, reattached new valve and reconnected water lines. Bled the lines and turned back on. Make sure temp in freezer stays at recommended temps for ice making.

Turn off water, un-plug refrigerator, dis-connect water, un-screw bracket, remove valve and replace same way...Very easy

Popped the top... disconnected wiring... dropped the front... replaced coils... reversed sequence... done deal. No hassle, no worries, easy as 1-2-3!

Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.

Followed instructions and the repair went very smooth from start to finish. From getting tools out of tool tray to putting them back it took 15 minutes.

There was a small plate and 2 screws holding the 2 coils. I just removed the screws, unplugged the 2 coils, plugged the new ones in and put the dryer back together.

After reading other peoples problems i decided it must be the coils after looking at the picture of the part I looked at the dryer to find were the part was. it was right in front behind the inspection cover. so i order the part. it came very fast.these are not the first parts i have purchased from Partselect.the web site is newer now and i am glad because reading other peoples problems help me decide what was wrong with mine.PS Always clean every thing inside the dryer!! 15-20 min job one screw driver! (19 year old unit works fine)thanks to Partselect!!!

My dryer was heating up very briefly blowing hot air initially then cool. I have a stacking washer/dryer set (2002). I initially turned off the gas valve at the wall, ran the dry for several minutes to clear the gas line, then unplugged the power. I was then able to pop the top using a flathead screw driver, securely prop it open, unhook the wiring harness to the front panel, unscrew the two front panel screws, and remove the entire front without having to unstack the units. From there, you remove the two screws holding the bracket over the coils (2 of them), remove the electrical connectors attached to both coils and replaced them with the new ones. I then replaced all brackets, screws, and such (you'll need to lift the drum when putting the front back on and make sure it is lined up), plugged it back into power and turned on the gas to test the unit which worked perfectly. The 62% of the time seems to be an accurate figure as nothing else had to be done to the unit. Pretty easy stuff...good luck.

Everything I needed to know was already on your website. Prying off the top of the dryer (with a big screwdriver under the front of the top) was the hardest thing, since I was afraid I would break something. Only then can the front be removed (taking out just 2 phillips screws). The rest is easy.