F31C546CT0 Frigidaire Dryer - Instructions

removing was easy just open lower rear LH panel . Ordering was easy ,shipping seemed like alot? to install the new belt pop top of dryer I used a screw driver to help. remove front panel 2 screws then it also has about six clips may have to have gloves on so you do not skin your hands like I did.... lots of sharp edges. pay attention to the clips, so if they come off they will not be lost. panel will tilt slightly fwd then raise up and set aside. now you can slip the belt over the drum. I kept all the slack at the top till it was in position. the groved rubber side goes against the drum and the motor pully. then extend the spring tensioner into position . I rotated the drum a few times by hand to make sure everything was in position. replace front. check it is lined up well before forceing clips in. check felt material is properly in place, as you rotate it into position. push down top . good to go. I ran it for awhile watching everything work before placing it back in service. you may want to clean it out some while it is apart I used an air compressor and shop vac simultaniously as that seemed to work best. Wanted my son to do it as I think he had it over loaded as to why it broke? It maybe the bearings are going but it felt solid ?? I should find out in a month or so shich was which! I did not see any easy way to get to grease it. The belt was easy though pretty sure my son could have handled it!

1 Unplug the dryer and Raise top up by releasing the clips and fold back to expose the drum. 2. Take Phillips head screw driver and remove two screws inside the front dryer panel and then take flathead screwdriver to pop out both sides and set aside. 3. Lay on your stomach and reach inside to the belt pulley and push right so the belt will release then stand to either side of dryer and grab the belt and lift the drum up out of its bracket. 4. Go to the front and pull the drum out and replace the Rear Drum Bearing Kit . 5. Grab the front panel and remove the Top dryer guide and replace to match evenly with the bottom dryer guide by cutting at least 1/8 -1/4" from felt and use High temp adhesive to glue down. 6. Replace everything in order that was taken apart and reconnect electrical plug and start dryer.

I've replaced the rear plastic bearing on this dryer twice, so I am familiar with taking the unit apart. After replacing the bearing in December, the machine still made noise (which had been masked by how loud the bearing was). The belt didn't look so great and it's 13 years old, so I ordered one and a new idler pulley assembly.

First, I disconnected the power and pulled it out for access. Using a large blade screwdriver, popped the cover open from the two clips in front. Be sure to support the top cover when you open it on the tabs or they will bend - I propped it against the wall. I disconnected the two wires that go to the door switch, and then removed the two screws that hold the front panel and door in place and lifted/opened that and removed the front panel and set it aside.

Next, I removed the back access grill (2 screws) and popped the belt off the idler by relieving the tension on the belt. Using a 10mm socket, I removed the idler pivot bolt and idler arm assembly. I installed the new idler arm assembly in its place and reattached the spring.

Moving to the front of the dryer, I lifted the drum off the blower housing on which it was resting and took off the belt through the front of the dryer. I then replaced the belt in reverse. Back through the access panel on the rear, I put the new belt on the motor and idler.

Be sure to check that there are no flips in the belt. I rotate the drum by hand a couple of revolutions to be certain.

I then reinstalled the front cover and door, reconnected the door switch, replaced the access panel and put the cover back down, popping the clips into place.

Put the dryer back in place, reconnected the exhaust and plugged it in. Voila - quiet dryer.

As an aside, I also took the time to clean the lint out of the blower and exhaust with a vacuum cleaner hose.

I unplugged the dryer. Undid the top by taking out 2 screws and mounts on each side of the back. There were two screws in the front panel that had to be removed. One on each side. Then I took the two wires off the killer switch on the door. Marking which was top and which was bottom. Then I removed the front panel. Then I undid the drum which had 3 screws in. I took out the drum to find the problem. I replaced the drum putting the belt on. Then I took off the back panel at the bottom of the dryer to get at the idler arm. Took off the spring and unhooked the arm. I put the new arm on and replaced the spring. I then put the belt on to the pulley and closed up the back panel. I put back the front panel. I put the top back on. I plugged it back in and turned it on and it worked!

I basically followed the video instructions on your website. Pretty simple but ran into an issue pre-threading the 3 self taping screws into the spindle bearing. The screws provided were blunt on the end and did not tap easily at all. I used the existing screws that were much more "sharp" and worked much better. Also, the new screws were Philips drive and due to the amount of torque trying to self tap nearly stripped them out. The old sharper screws were square drive which had a better bite. So basically, I used the old screws to self tap and then used the new screws for the final installation.
It took a long time to clean all the lint out from the inside of the dryer. The motor was completely embedded with lint and animal hair. You may want to suggest that a good cleaning may be needed so bring a shop vac...and also something to carefully pick the lint balls out from around the motor armature and bearing area. Overall the video instructions were really a big help!

Almost exactly as per the videos available on the PartSelect web site. The only additional information that would help is that the vent on the back of the unit can be removed to allow for access to the belt spring pulley. This avoids having to reach around from the front of the unit and feel your way to remove and re-install the belt.

All I did was push the new part into the machine! So easy!

1. Slid putty knife under each side of front of dryer to release lid.
2. Removed 2 screws from front of drum to release door assembly.
3. Removed wires from door switch.
3. Cleaned lint out of inside of dryer.
4. Removed old felt seals, upper & lower.
5. Removed old glue with goof off type remover.
6. Glued new seals on & held then in place with clothes pins. (there was enough glue in the tube that came with the upper glide for both seals)
7. Put dryer back together.
**Ensure you verify the correct felt seal pieces with the model number of your dryer, usually on inside of door.

Unplugged the drier, a couple of screws, remove the wires (take a picture of the wires with your cell phone to remember how they go back, twist out the thermostat. Installation is the reverse. A piece of cake.

Removed rear inspection plate, removed pulley spring and one hex bolt, replaced in reverse order. Very simple removal and install for this. Glad to see that Part Select still had parts for this 22 year old drier.

First I unpluged the machine, then opened the top with a flat head screw driver. Then I removed the two screws inside, unpluged the door sensor. (makes it stop when opened) Removed old gasket, cleaned with emery cloth, cleaned the residue and applied the glue provided. Waited about 1 min. and applied the new gasket leaving about 1/8'' of it hanging over the door facing the drum.

Watched on-line video, then applied those steps.
1. Pop the front of the deck loose using putty knife to depress clips;
2. Disconnect wires from light and door switch;
(Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.)
3. Remove lint filter mount screws and mount from bottom of door opening;
4. Cut drum belt with wire-cutters and removed it;
5. Remove drum support clip from top center of front panel;
6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel;
7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front;
[While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.]
8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.);
9. Have a second person hold the new ball hitch in position while starting screws, if necessary;
10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip;
11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel;
12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver;
13. Start drum belt on motor shaft and position against tensioner pulley;
14. Feed drum through front of machine and loop belt over rear of drum;
15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley;
16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing;
17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.

For me it wasn't even a repair, but rather, open the package, take out and discard the old lint tray and pop the new one in! Done. I didn't have to replace the frame. I would like to comment on how easy ordering was from partselect.com and how quickly the part arrived. Very satisfied customer! Thank you!

I unscrewed the old the lint screen FRAME and easily removed it, replacing it with the new one. The new lint -- SCREEN -- just needed to be squeezed here and there, and molded into a better shape. The screen itself, arrived flattened on the bottom, causing it to be too wide and difficult to remove from the frame. I easily molded it with my hands into the shape of the previous one and it slipped right into place. ( Shaped like an oval, flexible sack.) VERY easy!

First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!