FDG747RET0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Justin from Opelousas, LA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
off balance and noisy operation
removed the drum out the front and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from West Reading, PA
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clothes were getting caught between the drum and frame.
I used a putty knife to release the clips that hold the top in place. I then removed the screws that hold the front panel on. I pulled off the old drum glide and lower seal and scraped off the reside with a chisel. Acetone removed all the old adhesive very quickly. I applied the glue to both gaskets and applied to dryer. I used clothes pins to hold everything in place and waited overnight just to make sure everything was dry. I reassembled everything and its been working well ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Farmington, MO
- Parts Used:
- 5303937139, 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Worn out bearing.
Took out the drum by removing rear bearing and replaced with new one. Replaced top glides at same time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Davison, MI
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Rust marks on clothes during drying cycle.
I'm not very mechanically inclined, but even I thought this was a pretty easy repair. Just pull off the old seal and glide and glue on the new one. I let the glue dry over night, but in reality it probably would have been fine to use the dryer after an hour or so. We've been laundry all day and everything seems tip-top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from spring grove, IL
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
cloths getting caught between drum front cover
1)Unplugged unit from out let 2) Lifted top cover from base by prying up from the from the corners back is hinged 3) removed wires for door switch , removed a screw on the left and right from front. 4) pull front cover out from the top untill it clears drum then lift straight up off bottom clips. 5) scrape off old felt strip and guides 6) Sand untill all felt residue gone apply new glue to front cover wait a few minutes for glue to get tacky 7) clean out all the lint build up Checking from time to time that guide assemble is in place on front cover. 8) reinstall front cover when glue is dry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Flowery Branch, GA
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dryer was making loud squeak
This was for my Daughter's dryer. A helper really makes this quick and easy. First of all-UNPLUG the unit from the wall. I pried the top up with flat screwdriver. Laid the top back against wall. Removed the two wires from the door cut-off switch. Then removed the two screw attaching the front to the cabinet. Removed the small access panel on back of cabinet. Depressed the belt tensioner to release pressure on the leather drive belt. Went back to front, pushed the belt to the rear of cabinet, then lifted the back of drum to pop the bearing up and out of the plastic cup. I then tilted the drum forward and down and removed through front of cabinet. Reached inside the drum with Phillips screwdriver, removing the two screws to realease the bearing and BB bracket from back of drum. I attached the new bearing cup with BB to the back of cabinet, filling the cup with the high temp grease provided in the cup. Before installing the new bearing on the drum, I ran the new screws into and back out of the new bearing to cut the threads, making it easier to attach on the drum. I then put the drum back into the cabinet popping the bearing into the top of the plastic cup. Next I went to the back, put a bit of grease on the shaft that the tensioner bearing rides on. I re-set the belt on the tensioner, making sure the belt was back in the original position around the drum. I then re-attached the front cabinet centering the front of the drum on the felt. This felt supports the front of the drum. I manually gave the drum a few turns to make sure the drum was centered properly, and belt was mounted correctly. I then re-attached the two wires to the door switch. Slid the dryer into position, inserted the plug back into the outlet. Turmed it on, and now the dryer runs like new again. My Daughter is happy again. You will want to have a vac handy because it is unbelievable how much lint and dust are in the cabinet. I also took the filter bracket apart and cleaned it too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gale from Portland, OR
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud squealing
Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from harrison, AR
- Parts Used:
- 5303937139, 5303283286, 131302800
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
the dryer was eating my clothes
I took off the front of the dryer where the felt liner was located. Took off the old glide and scraped off the old glue with the razor blade. Took the tube of glue from the package and put glue where the old was and pressed the new felt on the dryer front. I then put it together and waited till morning to do a load of clothes. It works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Cottonwood, CA
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
squeek in rear bearing
There are really good instructions with photos on line - search squeeky dryer. I would add that it is easier if you mount the new bearing assembly on the drum before placing the drum back in the dryer cabinet. I guess this is obvious but was not stated in the referenced instructions. The round bearing slotts fairly easily into the plastic pillow block mounted on the back of the cabinet. Just make sure the small ball bearing remains in the center groove - lots of greese will help this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Merrick, NY
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Washer needed back bearing & drum guides
Watched two videos...totally easy. Might have been able to stumble my way through it in 3 times the time. Watched the video and entire fix took about 45 minutes...awesome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Kinderhook, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
loud squeealing noise from dryer during operation
The part arrived just in the nick of time as my wife and daughter had strung up rope all over the family room to dry clothes. My son helped me lower the dryer to floor level ( this is a stackable washer/dryer set) Removed the top and front of cabinet. Removed the belt and popped out the drum. Took this opportunity to clean the amazing amount of lint from the blower housing and discharge hose ( it is my opinion that the accumulation of lint and the subsequent rise in operating temperature is the main cause of this bearing failure) Removed and replaced the rear bearing and greased it. Reassembled the drum,installed the belt and reassembled the cabinet. the only tools used were a screwdriver and a nut driver....and of course a vacuum cleaner. The rebuild kit is very complete and is the only way to go. Thanks for your fast delivery time, one more clothes line in the family room and I wouldn't be able to watch T.V.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Mauston, WI
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud squeeking when ran
Followed online video. All went smooth. Runs great!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Aurora, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Drum Squeeking
Replace the Drum Bearing and Shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Kirkland, WA
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
small brown burn like marks on clothes.
The online descriptions were very helpful. I used a wooden kitchen fork to pry open the top of the dryer from the front, about 3 inches in from each side. Two metal springs hold the lid. The wire harness was on the right and two disconnects were easy to separate. Remember to disconnect power before you start. On the inside on the left and right sides are two screws which hold the front on. Remove these screws and the front panel will lean forward. Remember to support the drum as you pull the front off. Remove both top and bottom felt seals. I used a putty knife to aid in the removal of seals. Scrap the residue with the putty knife to remove. Run a bead of glue all around and let set for two minutes. Place top drum guide on first, and center on top. Put lower felt seal on next and tie a rope all around on top of felt, to hold in place while glue dries. Let dry for 30 minutes and remove the rope. Reassembly dryer. Test on low heat. It really is easy to do. Celebrate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from League City, TX
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Brown Streaks on Clothes
Pry top up, unfasten front side screws and pull front side away. Scrape off old felt liners and old glue from the front side drum rails. This was the hardest part of the job. I used a Citrus paint remover to help soften the old glue. Clean metal up with spay soap and water. Re-glue new liner in place. Re-assemble dryer.
Was this instruction helpful to you?
Thank you for voting!