DE250EDV4 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jamison from clayton, GA
- Parts Used:
- 5303281153, 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The drum was out of balance
I removed the panel's that enclosed the drum, removed the drum and cleaned all the lint around the drum, heat panel, drive motor, and switch's.
removed the old support bearing and grounding ball then applied grease into the new support hub and reinstalled the new hub and grounding ball and then reassembled the dryer. Runs like it was new.
removed the old support bearing and grounding ball then applied grease into the new support hub and reinstalled the new hub and grounding ball and then reassembled the dryer. Runs like it was new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Bartow, WV
- Parts Used:
- 5303281153, 131825900, 5303281153, 131724301
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
we heard the most deafening screech! when we investigated we found that the plastic part that the shaft rested in was worn, unevenly and the shaft end was scored. (we live in a house with 8 people so a fast fix was needed) I looked up the part on a sears site. when I checked the part avalibility I f
we removed the top of the dryer which was clipped on. then removed the front, including the door, being careful to unhook the electrical elements. then we removed the screws that attached the dryer drum to the back of the shaft. then we took the shaft out of the bracket. then we removed the plate from the back of the dryer that held the ball, the bearing and the bracket together. then we waited for parts and thanked God that the weather was fair so we could hang our clean clothes out!!! the parts came ahead of the rain so it was reverse order. then try the dryer!!!fantastic!! to qoute my kids "you rock"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from New York, NY
- Parts Used:
- 5308015435
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The knob of my dryer broke
I had a repair man fix it- it went very well
Was this instruction helpful to you?
Thank you for voting!
they where just wore out.
Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Mont Pelier, VT
- Parts Used:
- 5303281153, 5303281153, 131825900, 5303281153, 131724301
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
rear support bearing squeeking
removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble.
this should be available as a kit, and should include high temp grease to put in bearing bracket
this should be available as a kit, and should include high temp grease to put in bearing bracket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryant from tolna, ND
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer did not turn
put the new part on with ease took 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Bainbridge, PA
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door would not stay shut.
The other door latch broke and fell out. I simply pushed the New Door Latch in the hole, and it snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond Frattone from Richboro, PA
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not close because of broken female latch.
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald R from Dalton, GA
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door latch broke
It was super easy ! The part came and I had it done in less than ten minutes. No mechanical skills necessary !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hernando, MS
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door Would Not Close
Inserted clasp in frame of door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bennie J from Kite, GA
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer making lots of noise
Remove small back plate near floor with 1/4 inch nutdriver unscrewing two screws. Lay the small plate to the side. Remove dryer belt from around pulleys by pulling up on the old idle arm near main spring. This will loosen tension of the belt. Belt just needs to be removed from only around the two pulleys. Detached spring from old idle assembly. The old assembly will just lift out. Reassemble in reverse order with new assembly from Parts Select. Takes less than 5 minutes. Extremely easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mayfield, KY
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
put door catch in hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from Bell Gardens, CA
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Loud Squeaking
Very simple. Pop the top open released the beld from the back it's easier that way the video was very helpful the sound was so bad you can hear it from a few houses down after year of just using it like that I figured I ha d nothing to loose great price great instructions now it sounds just as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from East Nassau, NY
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Catch broke
My son kept slamming the door wrong and eventually the catch broke and two and feel out. My husband is the handy man of the family, but has been so busy that I was just duck tapping the door close. Finally, I decided to see if I could look up the part. Found it on here, ordered it, and replaced it all myself! Proud mother right here! Very easy. Works great.
Was this instruction helpful to you?
Thank you for voting!