DE250EDF5 Frigidaire Dryer - Instructions

took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.

Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.

This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.

The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.

Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.

I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.

I highly recommend watching the repair video. I could stop the instructions and do the procedure then resume instructions for the next step. I would recommend you have a second person to help lift the drum up & out of the dryer frame. And ladies please instruct your husbands to watch the video all the way through. Mine lifted the top off the dryer and stuck his hand in and cut his finger immediately on a sharp piece of metal. You know because they don't need to read the instructions.

Hired a professional!

I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.

It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!

removed top-removed front-removed belt-removed drum (I didn't know how the drum came out WITH the bearing so I unscrewed the 3 middle screws on the back of the drum which released it from the bearing)- removed the bearing-that was when I knew what to order. installed the bearing on the drum before assembling all in reverse order. I wasn't sure how much grease to use so I used about 1/3 of it.

It was super easy! I followed the PartSelect video and everything went fine. Getting the drum out of the machine was a bit tricky but once it was out, the rear bearing kit went in without any problems.

followed the Video instruction which were provided. Dryer works like brand new.

i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!