CRER442AS0 Frigidaire Dryer - Instructions

removed the screws, disconnected the wires. installed the new elements replaced the wires.

Did repairs by hand, took longer to open box and remove packaging that to install the parts. Total time from mail box to repair complete- 3 Minutes.

After entering the info on the dryer into the PartSelect site, it brought up a list of parts, and a diagram showing where all parts go on the dryer.
Clicking on the knob description brought up a photo which proved beyond a shadow of doubt that this was the correct part. At a cost of $5, who wouldn't pay for the expedited freight also? For 6 months we've kept the pliars on top of the dryer to use in place of the worn out knob. Don't lose the address to this site. Jim

First, I unplugged the dryer. Then, I removed the back panel from the controls section (6 screws), disconnected the old switch and reconnected the new switch. Positioning the switch in the control panel took some figuring out, but once I realized that the switch slots into place, and then gets locked in by turning 1/8 of a turn, it worked fine.

Replacing the knobs was a cinch, just popped them in place. Now the controls are like new again.

Frigidaire controls are really junk, though. I won't be surprised if I have to do this repair again in two years.

Once the part was located all I needed to do was pop the old part off and pop the new part on. It took less than a minute from start to finish. It also saved me an $80 service call.

1) Removed Top Dryer Cover (pushed 2 compression clips on front side 1" from top and 2" in from each side) to gain access to terminal block in rear.
2) Removed 2 screws over terminal block cover and 2 screws holding bad terminal block in place. Removed 3 screws holding bad power cord,
3) Removed good terminal connectors from bad terminal block and reinstalled them in the new terminal block.
4) Cut dryer wire from bad terminal block connector and soldered (optional) them to the new terminal block connector. Installed this connector into the new terminal block.
5) Installed new terminal block in dryer with 2 screws.
6) Installed new power cord on new terminal block ensuring contacts were tight and cord had pull guard properly installed. Reinstalled terminal block cover with 2 screws.
7) Reinstalled Dryer Top Cover.

took off back vent panel, removed belt from idler pulley. tried motor again to see if it would work under no load. motor was not seized just would not run. concluded it was the motor. I removed the 2 mounting screws from the back of motor area. from there removed top of dryer and bolts for the front door panel. propped open the door panel to get to the fan housing and 2 front motor mount screws. disconnect the fan wires. pull out fan and motor assembly from front of dryer. I used a medium sized locking wrench behind the pulley and then mounted the wrench (attached behind the pulley in a vise) from there I was able to use a socket to take off the plastic nut at the end of the fan. Notice that it is a reverse thread so don't strip it. dismount motor from bracket and reasmble with new motor. all the steps in reverse. Since the motor was out it just made sense to replaced the belt at this time. took about 45 minutes to disassemble and just over an hour to get it all back together. Make sure you clean out the lint box from inside the dryer.. over the years it will accumulate a lot of nasty dust bunnies. check that all the surfaces are clear of dust and the back of the vent pipe to..

It was too easy: 1) remove the back of the control panel 2) disconnect wires to the switches and mark them for reassembly- I used masking tape and gave each wire and connector a letter- "a" "b" "c" etc; 3) remove the top of dryer by using a flat head screwdriver to pop the 2 pressure fasteners on the front; 4) remove the front of the dryer- remove the 2 screws fastening the front panel to the sides and lift up until the bottom pressure fasteners pop; 5) remove the belt from the pulley and tensioner- I used a digital camera to take pictures so I knew how to re-thread the belt; 6) remove the drum- pull up on the back of the drum with the belt and then pull the drum through the front of the dryer-it's a little smaller than the front opening so you need to pull on the sides of the dryer; 7) replace the heating element by (a) removing the overheat sensor and (b) removing three screws to remove the heating element from the back of the dryer; 8) replacing the rear drum bearing by (a) removing the bearing asssembly from the back of the dryer-2 screws, and (b) removing the bearing roller from the back of the drum- 3 screws; 9) assembly is the reverse of disassembly. Again it's too easy. I'm a lawyer with no mechanical training. Thanks to Parts Select for making finding the parts easy and saving me a lot of money.

I first watched the video. Had I not done that, I probably would have started looking for a new dryer. The repair is simple and I feel like now I could repair just about anything on the dryer.

The first thing I did was cheked the electrical panel and breaker, then I checked the electrical cord, then I did check the motor on the bottom of the machine (that may be is the blower motor) looking for any indication of burned parts or broken, then I checked the on-off switch with a voltmeter looking for continuity and it was fine. Then I checked the timer switch and it was fine as well. Finally, I took the lid off the top of the dryer machine to check the thermostat and themal limiter fuse. The thermostat was fine but the thermal fuse was open. So after doing some research to understand how the fuse work I decided to place an order to get a new fuse. I installed it and the dryer started working again. After replacing the fuse I monitored the dryer machine while operating it and worked fine. Why the fuse was open or was damaged? It is the first time I have problems w/ the dryer. I checked the end of the conduct line that guide the air out and I noticed and have to clean the end of it because it was dirt. Because it was not completly clean, the dryer got overheated. It took me sometime to figure out the problem but I learned, save me money and the best part was that I do it myself : )

I removed the broken door latch & strike with pliers. Then I pushed the new parts into place

Let me start by saying that I am a stay-at-home mommy of 2-year-old twin girls so if I can do this, you can too.
1. I disconntected the dryer from the outlet.
2. Then I had to pop open the top of the dryer. I had to wedge a screwdriver underneath the top lid (towards the front corners) in order to open the top.
3. Looking into the dryer from the top I could see a few screws I needed to remove that were along the sides of the drum. After removing the screws, I was able to remove the front panel of the dryer exposing the drum.
4. The seal that I needed to repair was located on the front panel. I had to remove the old seal (I had to scrap to get some of it removed).
5. I applied the adhesive then attached the upper and lower seals.
6. I let the seals dry for a few minutes then replaced the ront panel. In replacing the panel, the seals need to fit around the drum. You need to be careful in fitting the drum so that the seals remain intact and not pushed out of place.
7. Then, I simply replaced the screws to the front panel and secured the top lid back in place.
FYI: I did have a problem with the lower seal, in placing the drum over the seals, the lower was pushed out of place without me knowing. A few days later, the dryer was making a noise and clothes were still getting caught. After opening the dryer and examining the seal, I needed to reattach the seal. I was out of the adhesive but was able to use Gorilla glue (can withstand any temperature once it is dry). Works good as new now.
FYI: I also have to add that the actual replacing of the seals did not actually take 2 hours but since the dryer was opened, I took advantage and thoroughly cleaned the inside of the dryer.

I took the new latch out of the package and snapped it into place. It took about 15 seconds, and that included the walk to the laundry room!

I waded into this project without knowing what I was doing and as a result did much more work than was needed. What I should have done was 1) open access panel at lower left of back of dryer and rmove belt from pully 2) push screwdriver in against clips in seem at top front of dryer (where top meets face) and lift top up and off hinges at back 3) remove screws holding front of dryer to the sides of the dryer cabinet (about 1 foot down) and swing front down on hinges at bottom 4) lift dryer drum straight up out of the bracket at the back of the dryer 5) remove wires from the dryer element and heat sensor on the heater pan (about 4 and 1 o'clock respectively wires are on tight, may need plieres) 6) unscrew heater pan from back of dryer 7) remove heat sensor from old heater pan and put on new heater pan 8) screw new heater pan to back of dryer 9) replace wires to elements and sensor, you may want to "crimp" the connectors onto the tabs 10) replace dryer drum slipping back into back bracket, be sure that dryer belt is around drum as when you openned the dryer 11) lift up front so that drum fits around and is supported by flange molded into front 12) replace screws that attach front to dryer cabinet 13) replace top of dryer (put back on hinges at back and lower onto clips in front 14) put dryer belt back on pully and replace access plate.

remove the rear lower left vent cover to get access the belt tensioner and pulley. then pop the top section up with a flathead screwdriver in the front, freeing it from the popclips. Then remove two screws from the back side of the front section releasing the drum. loop the belt around the drum.