LCE756BS8 Frigidaire Dryer - Instructions

Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.

I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.

my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!

Your company was really easy to work with. Your company sent the piece very quickly and we were able to repair it literally in about one minute. It was a fantastic and easy solution. Thank you!

I pulled the knob off,and put the new one on. The amazing part of the story is , I got the part from you in ONE DAY!!!!!!!!!!!!!!!!!!!!!! Thanks Mary

Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.

I have used this company twice now and both times have been a good experience. Would highly recommend!

Unplugged dryer, Removed top of dryer, Removed electrical connection to thermal limiter, tested thermal limiter with meter and found that it was bad,removed defective limiter, ordered part, waited for part (1day), put new thermal limiter in dryer. reattached connections, put top of dryer back on, plugged in dryer, attempted dryer start up and it worked. Very easy because of the information I got on this site. Thank you

lifed the lid .remove oud hose and replaced with new hose

Used flat head screw driver to pry up the top. Removed front cover. Pushed tension idler pulley back to release tension on the belt. Removed old belt. Put new belt on motor pulley and idler pulley. Started one edge on main pulley and slowly rotated main pulley until the belt popped in place. Tested on spin cycle. Replaced front cover and top. Unfortunately, this didn't stop the noise...turned out a shipping screw was still in place. Removed the shipping screw and voila! no noise. It's always the little things that get ya.

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.

disconnected the dryer; cleaned the duct. I reconnected everything and started it up again and within seconds tripped the breaker.Decided probably the thermal limiter was faulty, so ordered new one from you. After it arrived I watched video, then removed the top and front, pulled drum to give me some workroom, replaced the limiter, reassembled in reverse order.I then reset the breaker, plugged the dryer in. Runs perfect.The drum was a challenge - so I used a wooden wedge to support from the front and opened the 12 by 12 rear port to access and reset the pulley cable assembly.

Removed top from dryer. Saw I could get to Limiter without removing dryer drum.Removed Limiter with phillips head screwdriver and wires with needle nose pliers. Replaced wires and secured Limiter to dryer works like a new one.

Used wiring diagram in back of machine control head. UNPLUG DRYER! Removed panel off control head and motor access cover at bottom of dryer. Tested door switch continuity first, then continuity from control timer to motor. Found open circuit on white wire. Opened top of machine (pops up at front) and found thermal limiter on back of machine was burned and caused open circuit. It's a little awkward to get to the screws with the drum in place. Use a 30º angle ratching 1/4" ratchet wrench with a magnetic #2 phillips bit.

The most difficult part of the process was removing the panels to gain access to the drum. After removing the drum, the heater assembly is secured by 4 screws and is easily removed. The heater assembly is easily installed with the 4 screws and reattaching the wiring. The top panel should be removed to allow easy reinstallation of the drum. If replacing the drum belt, there is an access panel in the back of the unit that will allow you to slip the belt over the motor and idler pulleys.