LCE756BS8 Frigidaire Dryer - Instructions

The repair went smoothly considering I am a rookie. The repair videos on your site are great. Followed the techs instructions and got thru it fine.

Thanks,

Jim

I watched the video you had. Did what the man said, checked out the parts, and orded the new ones. Then installed , as per video. It was Fun.

Disconnect from electric and water supply, and move appliance to an area where you can access front, rear, and top of dryer. On rear of dryer remove the 2 screws on the small square panel, remove panel to expose dryer motor and tensioner pulley. On top of dryer remove the 4 front screws, but not the center screw, it is not necessary as it is holding something on the inside. Open dryer door and remove the lint trap, exposing the vent. Remove the 2 plastic snaps using a flat screwdriver. This will disconnect the vent from the front panel. Next remove the 2 small screws on top sides of the control panel. Remove the 2 screws on angled back panel, and remove panel. Remove approx. 10 more screws holding the under panel on, and on the bottom of control panel. Remove under panel, and slide control panel up and pull out, disconnect electrical connection on left side. Remove front off of dryer carefully, the weight of the drum is holding it in place. Vacuum everything, remove broken belt, put new belt on drum, rib side down, and slide all the way back all around. Go to rear of dryer and remove tensioner arm off of its post, there is a slot to do so, put belt on motor pulley, reapply tensioner arm in position so belt goes around it. Spin the drum a few times by pulling on the belt to make sure there are no twists. Place the front of dryer back on, put two corner screws in the top, and reseat the drum. Reconnect the electrical connection inside dryer you disconnected earlier, plug in dryer, and turn on to test. If it heats and turns well done, if not good luck. Unplug, slide vent back in, reinstall plastic clips, and ensure that vent is seated in the foam pad on the exhaust motor vent. Work backwards and put panels back in place with screws. Job done.

Removed old belt. Installed new belt.

removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!

just put it in the dryer filter area

I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.

Popped the tub cover off....replaced with new one.
Thank you so much for a speedy delivery.

just changed filter

Pulled off old
Pushed on new

purchased part (drum belt) didn't fit the drum it was larger,, i select the size according to model number and serial number but unfortunately it was wasting of time and money and i still don't have dryer.

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

Drop in the new beautiful filter without holes.

insert knob.....

easy stuff but was impressed with the ordering and expeditious delivery of the product.

Great Job!!

Lift washer lid by jerking the lid up and open. Remove front panel by removing 2 screws at front bottom and guiding tabs out of slots. Locate tabs on tub cover and gently pry loose with a flat blade screwdriver or putty knife. Remove tub cover and inspect seal area for damage or debris. Replace new tub cover on tub and align and fasten each tab. Ensure that lid is securely fastened to tub by pressing top of cover down and visually inspecting that each tab is engaged with tub hooks. Replace front panel. Use anti-seize grease when replacing the 2 front panel screws. Use a small amount of petroleum jelly on the top lid spring clips before closing washer top. (The last 2 tips will help any future opening of the washer.)