GLEQ642CAS1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Natalie from Jasper, TN
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud Noise in dryer
Removed the top and front of dryer. Removed the old bearing and held the new bearing in place while my husband tightened the bearing into place......easy......now the dryer runs quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from New Iberia, LA
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
Unhooked wires turned switch to the left put new switch in and turned it to the right 1/4 turn and put knob on front of switch this is the best parts web I have been on so far.
Was this instruction helpful to you?
Thank you for voting!
door handle an screws missing
doo handle snapped in place an replced screws that were missing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Baltimore, MD
- Parts Used:
- 131450300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint filter bent
Vacuumed lint and inserted new filter.
Was this instruction helpful to you?
Thank you for voting!
they where just wore out.
Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.
Was this instruction helpful to you?
Thank you for voting!
Dryer drive belt broke
I opened top section with a screwdriver, pushing in the release.
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Sacramento, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Due to weather exposure, the handle fatigued and broke in several parts.
You simply pry the old handle off with a flathead screwdriver, and then line up the new handle and snap it into place. It took less than 30 seconds! A breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Minot, ND
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken belt
Remove drum, replace belt, return drum
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Raritan, NJ
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer not heating up and shutting down
remove 2 screws rear of drier at top slid the top back and off removed 4 screws on front electronic read out panel and disconnected two wire harness plugs remove the panel removed 2 screws for lower panel at top on either side of rotating drum,tilted machine back removed two screws at very bottom on front of dryer to remove lower panel ,and remove the lower 2 screws to remove front panel.lifted rotating drum up and out of drier ,removed 4 wires on the heating element and four retaining screws from rear of drier to releases the heating element,than reverse the procedure for assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Enterprise, AL
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer stopped putting out heat.
The repair went very well for a 1st timer. Instructions were very easy to follow. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Strongsville, OH
- Parts Used:
- 131873500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old timer knob was broken
New knob placed on machine...a no brainer. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from New York, NY
- Parts Used:
- 131873500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob had broken off
Just plugged it right in Thank you for having the knob in stock. Received the knob within a matter of 3days. That is prompt service. Bernard
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Greenwood, IN
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer not producing heat
Once the part arrived, I logged back into my order and watched the part installation video as I did the repair. The video was perfect, it made doing the repair easy and safe. Best part is I didn't end up with any extra screws which was good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MANUEL from SAN JACINTO, CA
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum belt
so easy my daughter installed it the video was very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from ANCHORAGE, AK
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer spun but didn't heat.
It was a closet type washer/dryer combo. With little space to work I needed to know how to get at the heating element to test it. Was told the tumbler had to come out the front to expose the element. Made the job easy without having to figure that out.
Was this instruction helpful to you?
Thank you for voting!