FSGC447GHS0 Frigidaire Dryer - Instructions

Pulled old knob off and replaced with new knob. The hardest part of the repair was finding the part and partselect made that easy as well.

From opening the mailed package to complete installation of 3 knows took about 3 minutes total time very easy to order on you web site and the product came in so fast I thought that you were still processing the paperwork. Thanks keep it the services.

replaced the knob. The key was the photos. It was celar that the part you had was the one I needed beacuse the phots were clear and with enough angles to assure me I was orederig what I needed.

I grabbed the new knob I ordered from Partselect.com with my right hand, aligned it, and put it on. Works like a charm!

I had my landscape guy, who volunteered to look at the dryer since he's also an electrician, come in and take a quick look. he turned the knob, pulled it off and told me the inside was cracked so it would not grab the turn mechanism. Who knew? I got the model number from the dryer door, checked in on the internet for Fridgedaire parts, found Partselect.com, ordered part, came next day, knob fits, dryer works. end of story. THANK U!!!

I opened the envelope that was waiting on the porch when I got home from work, opened it up, and pushed it on the shaft. It fit like a glove and looks more durable than the old one was. She'll never know I broke it. :)

Got the proper part and it worked great

Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.

Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.

Removed access plate in rear, raised top panel, removed two screws holding front panel (with door) put new belt over drum. Threaded belt through path between motor drive and idler wheel. Put everything back together.

My order was shipped very promptly, and was received very quickly. It is wonderful to have this service available on the internet. I can remember how difficult it used to be chasing down parts before. This was impossible in smaller cities.

Popped the top... disconnected wiring... dropped the front... replaced coils... reversed sequence... done deal. No hassle, no worries, easy as 1-2-3!

My Son-in law did the repair. He removed the top, the front lower panel and finally the front panel with the door. It took a little more time than anticipated because there was not any explicit directions on how much to remove to replace the belt, but he got the job done and put it back together very quickly. Glad I have him to help when needed:).

Got the belt for my little bro's dryer . . . he and a friend tore into it without looking on how to do the job . 2 hours later dryer apart not fixed . . . LoL . . . Next day I get a Call asking me to find a repair manuel . . . I laught and told him to go to Youtube on his phone and the video would tell him how to do it ! He is back up and drying . . . Moral to this story . . . look before you leep !

I watched the video on the web site after selecting the part and it was pretty simple. Everything worked just like the video showed. Probably could have been done faster but I took time to vacuum the inside of the dryer out. Really liked the video.

I popped the dryer lid open by pressing on two latches with the flat putty knife. I found that I really needed another set of hands, so my son helped me with this project. I had to disassemble the front panel by unscrewing 2 screws on the sides and also 2 screws around the dryer timer knob, after removing all knobs. Also, I had to pry apart 2 of the front pieces because they are clipped together with plastic latches. I unhooked two wires from the starter switch and then gave a half twist to remove it from the opening. Once that was removed, I just replaced it with the new part and put everything back together in reverse order. I did test the dryer before putting back together, but make sure you unplug it again while assembling. I forgot and two wires touched and there was a big spark and popping noise. Fortunately, nothing was blown out and no one was shocked I had absolutely no experience with anything like this but found this website to be a huge help. I figured everything out just be looking at the diagrams and some other notes on-line. Thanks!