FSGC447GHS0 Frigidaire Dryer - Instructions

Unplug dryer.
Put up the top of the dryer at the front, remove 2 screws holding the front of the dryer to the sides and remove front of dryer. Locate ignition coil on lower left. Remove 2 screws and bracket over the two ignition coils. Replace coils and reassemble in reverse.
Everybody's happy.

The repair was simply removing metal guards from old knobs and placing the new ones on the dials.

What's remarkable, I ordered standard shipping and they were here the NEXT DAY~!

Great customer service.

fIA

Cover of the dryer pops off and hinges back. Use a flat screw driver to pop the clips on the front sides. Two phillips head screws hold the front panel on. Remove them then lift the panel off the clips at the bottom. Two phillips head hold the Ignition Coil bracket in place. Take note of the direction of the cable connection, it's not marked. Dryer would ignite intermittently. Clothes were not dry after 1 hour.

removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!

Removed 2 rear philips sheetmetal screws. Popped lid off w/ flathead screwdriver. Rotated old switch counterclockwise. Moved 2 terminals from old switch to new. Put everything back together in reverse order.

my experience was just like the other responses. top comes off, 2 screws and the front comes off and the screws to the solenoids come off. Replaced the solenoids and put everything back together.

I watched the video that I saw posted on youtube. My dryer did not have a panel on the back to remove, so the part was very easily accessible. I simply took the old switch off and replaced it with the new one. The most impressive part was receiving the part so quickly. That was awesome! It saved me a trip to the laundromat. I really did not expect to receive it so quickly. Thank you!!!

Pulled the unit from the wall, Unpluged the power and removed the back cover behind the switches. twisted the switch removed and removed the wire, inserted switch and turned in place. Put the button on and good to go.

I ordered replacement knobs...installed them, and the dryer was ready to go...no problem!!

I removed all but one screw on the back of the control panel and slid the panel down and to the left. Then I jiggled and turned the start switch box out of the slot, unplugged it, plugged in the new switch, and put it back in the slot turning slightly to tighten into place. I replaced the screws and the repair was complete!

Removed burner, unpluged 2 plugs on coils. Removed 2 screws, replaced coils, pluged 2 plugs to coils replaced 2 screws. Reinstaled burner. Dryer works great.

Removed drum and replaced drum support bearing.

My Son-in law did the repair. He removed the top, the front lower panel and finally the front panel with the door. It took a little more time than anticipated because there was not any explicit directions on how much to remove to replace the belt, but he got the job done and put it back together very quickly. Glad I have him to help when needed:).

Got the belt for my little bro's dryer . . . he and a friend tore into it without looking on how to do the job . 2 hours later dryer apart not fixed . . . LoL . . . Next day I get a Call asking me to find a repair manuel . . . I laught and told him to go to Youtube on his phone and the video would tell him how to do it ! He is back up and drying . . . Moral to this story . . . look before you leep !

Dismantled the dryer to determine that the belt was broken. Called a local supply outlet to request a belt. They said they couldn't find one. Did an online search and found Part Select. Called with the model number and within three days the part was delivered. Replaced the belt and the dryer was working within an hour. Hardest part was getting the dryer out of the laundry room. I would certainly call PartSelect again if I needed a part.