FSG849GHQ0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from Sayville, NY
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Broken belt; Second one in 2-years.
I heard the dryer running, but I didn't hear it tumbling like usual, so I got suspicious. I popped the top off of the dryer to reveal a broken belt. Installation took 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Middlebury, VT
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken turn type start switch
just like the excellent video showed me. It was so easy and the web sight has a video to show me how to do it. Piece of cake! Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Woodland, ME
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Broken drive belt
Raised the lid, removed 2 little screws,slipped the front panel off, disconnected the safety switch, vacuumed everything, slipped on the drive belt and reversed my way out. It was way more easy than filling a grease gun!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Covington, WA
- Parts Used:
- 131845801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer Vent Was Very Clogged and Impossible To Clean
Removed two screws, removed gummed up and clogged vent cover and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from Henderson, NC
- Parts Used:
- 131644702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door handle broke off.
All I had to do was snap the new handle in place. The new handle was identical to the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BeLinda from Indianapolis, IN
- Parts Used:
- 131450300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter was broken
All I did was insert the new one! Service was excellent. I received it in one day!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Bella Vista, AR
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The plastic knob was wore of and couldn't turn to start dryer.
Unplug dryer from outlet.I removed the screws from the back panel behind the controls. The switch has 2 wires that slip on the switch terminals. I slipped them off, gently lifted the catch located on the switch and rotated switch which is just held in place by two slots. It fell off in my hand when slots were aligned. Copied part number, ordered part, replaced on dryer. Works like a charm. Part arrived in 2 days. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Willits, CA
- Parts Used:
- 131863007
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Loud screeching noise, barrel turned OK and Heater worked
I took the lower back panel off. Loosened the center bolt and took off the old Idler pulley. It looked brown in the middle and didn't roll well. But I wasn't sure if that was it, because the noise was so loud and sounded metal on metal. So I checked everything and vacuumed everything. After I got the new part it took me about 5 minutes to put the new one on. And dryer works fine. Thanks for the quick response and I saved about $200.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Oviedo, FL
- Parts Used:
- 5303937186
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
gas dryer starts but no heat
after checking on line, i shut off the gas and disconnected the burner unit from dryer. after removing unit i tested all electronic parts and found the igniter was bad. i removed same and ordered new part. when new part was delv. i reinstalled the unit and all worked like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Essexville, MI
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer ran, had no heat
Your website was very helpful in narrowing down and diaganosing the problem. A continuity tester verified an open solenoid. Ordered Sunday evening, parts arrived Tuesday. Ignition coils drop in place with a holddown bracket and one screw. Wiring harness is reattached. Front of dryer is put in place followed by the top. Plugged in the dryer (it is just commom sense to have the power off). Started dryer, of course it ran WITH heat. The end of the story is HAPPY WIFE, HAPPY LIFE. Happy to do business with you. Tom , MI
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from Oak Park, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer would heat up but shut off too early
pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.
Was this instruction helpful to you?
Thank you for voting!