FSEC346RHS1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- shajauna from Virginia, VA
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken start switch
I watched the video that I saw posted on youtube. My dryer did not have a panel on the back to remove, so the part was very easily accessible. I simply took the old switch off and replaced it with the new one. The most impressive part was receiving the part so quickly. That was awesome! It saved me a trip to the laundromat. I really did not expect to receive it so quickly. Thank you!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer Would Not Heat
I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marci A. from Neptune, NJ
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Appeared to be a failed belt
Appearances can be deceiving.....while dis-assembly was a piece of cake; the problem turned out to be failed welds on the dryer drum. REMEMBER this before you make a parts decision. Examine the problem.FIRST! (this comeing from a guy who used to Manage an appliance repair shop WAY back in the day....DUH!)Solution?....new dryer; repair cost too high. None the less...at least I have a spare belt !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Eldena, IL
- Parts Used:
- 5308015398
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer wont dry during one cycle, still doesn't
removed the two screws on the top at back of dryer then pryed up the front of the top, then removed the screws at the top of the front and pryed off the front of the dryer, the thermostat was at the bottom below the drum held on by two screws and had two wires on it. Fairly easy to replace but it did not solve my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi Dixner from Nashville, TN
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
start knob broke off
I removed all but one screw on the back of the control panel and slid the panel down and to the left. Then I jiggled and turned the start switch box out of the slot, unplugged it, plugged in the new switch, and put it back in the slot turning slightly to tighten into place. I replaced the screws and the repair was complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kennedy from Fairhope, AL
- Parts Used:
- 5303307893, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Loud squeaking
Removed drum and replaced drum support bearing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Devine, TX
- Parts Used:
- 134503600
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Broken belt or wore out !
Got the belt for my little bro's dryer . . . he and a friend tore into it without looking on how to do the job . 2 hours later dryer apart not fixed . . . LoL . . . Next day I get a Call asking me to find a repair manuel . . . I laught and told him to go to Youtube on his phone and the video would tell him how to do it ! He is back up and drying . . . Moral to this story . . . look before you leep !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Somerville, MA
- Parts Used:
- 131553900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no heat but otherwise ran fine
I used the posts on the site to ascertain the problem (fuze or element burnt out). The pictures were very helpful. I pulled the dryer to the floor and using my meter checked both the fuze and the element. The electrical diagrams were very helpful also. I took the dryer apart further to make sure the coil was indeed the problem. I then ordered the part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Lawrenceville, GA
- Parts Used:
- 134503600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Broken dryer belt
My Son-in law did the repair. He removed the top, the front lower panel and finally the front panel with the door. It took a little more time than anticipated because there was not any explicit directions on how much to remove to replace the belt, but he got the job done and put it back together very quickly. Glad I have him to help when needed:).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Midlothian, VA
- Parts Used:
- 131825900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
worn bearing
Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from CHINO HILLS, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace knob
took off old knob and put on new knob used my hands
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from bayside, NY
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
on/off knob replacement
Piece of cake to remove old knob and replace with the new. Really impressed with delivery of the part the next day. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamera from Fair Oaks Ranch, TX
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotary knob broke
Just slipped it on --- easy as that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from san diego, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had broken knobs
From opening the mailed package to complete installation of 3 knows took about 3 minutes total time very easy to order on you web site and the product came in so fast I thought that you were still processing the paperwork. Thanks keep it the services.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Coronado, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob on Dryer
Pulled broken knob off and pushed the new knob on. It was about as easy as it gets.
Was this instruction helpful to you?
Thank you for voting!