FER341ZAS2 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from CUMMING, GA
- Parts Used:
- 134222900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top hinge on clothes dryer separated, leaving door difficult to open/close
Ordered part from partselect.com. Part was back ordered; however they were very proactive in communicating status updates! When it arrived it was simply a matter of removing door using a philips screwdriver, installing the new hinge and presto - job complete! Kudos to partselect.com ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from SANTA BARBARA, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic door handle for dryer needed to be replaced.
Snapped the new door handle replacement from this site in place. Fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from TROUTDALE, OR
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer door handle broken
I just used a putty knife to remove the broken one. It just popped right off.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from BUFFALO, NY
- Parts Used:
- 134398300
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer start knob broke clean off
I YouTube'd how to repair it. It was super easy. Needed a power drill to get the screwsa off and a flat head screwdriver to pry off the wires but besides that it took about ten minutes and I was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from HAYESVILLE, NC
- Parts Used:
- 134844410
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken selector knob
Simply pressed knob on appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Mount Horeb, WI
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start Knob Broke
My wife simply removed the knob from the package and pushed it on. No tools were needed and she felt satisfaction that she was able to "fix" the problem on her own.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myrna from Apache Junction, AZ
- Parts Used:
- 134398300
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The start switch was broken
Took the front off the dryer and removed the old switch and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CLARK from JUNEAU, AK
- Parts Used:
- 134886700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken knob
removed knob..very easy instructions..took 10 min...very pleased with repair and fast order...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from Middletown, NY
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Tumbler not moving
Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan D from REDLANDS, CA
- Parts Used:
- 137551901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
the attached anchors and holes linled up about 80% of the time.
I cut off the four that didn't line up - I suppose since this was a gasket that fit several makes, I should expect this type of problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Yucca Valley, CA
- Parts Used:
- 134398500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken switch
Removed rear cover, unplug 2 spade connectors, twist out old switch, twistin new switch. plug connectors, install cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from IRONTON, MN
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drum belt broke
i removed two screws that hold the top of the dryer on at the back of the dryer then i removed a couple of screws that hold the front of the dryer on at the top of the front then i disconnected the two wiring connecters inside the front and a ground wire when the belt came i put it around the drum and took two screws out on the back of the dryer near the floor that hold a small panel in place to access the motor i put the belt on the motor and idler wheel and that was it put together and done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from converse, TX
- Parts Used:
- 134886700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The knob on the dryer broke
I basically looked on the back of the new knob and found the flat side.Then I match it to the flat side of the metal stud on the dryer .I then pushed it onto the stud on to the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from MCVEYTOWN, PA
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob broke to adjust temperatures on dryer
old knob was broken so didn't stay on and work so had to use pleris to adjust temperatures when needed but now just put new knob on and we are in buisness and like new again!!! So glad I found your company and had the knob i needed and fast service!! thanks :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Hillsborough, CA
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken start switch shaft
Removed 2 rear philips sheetmetal screws. Popped lid off w/ flathead screwdriver. Rotated old switch counterclockwise. Moved 2 terminals from old switch to new. Put everything back together in reverse order.
Was this instruction helpful to you?
Thank you for voting!