KER331ZAS2 Frigidaire Dryer - Instructions

Take the top off the dryer. Once it's off, start inserting the bands from the inside. From the top or inside, control and move the drum as needed to insert band in place. Once band is in place, and holes line up, press down till you hear it snap in place. Repeat process with second band.

I took the lower back panel off. Loosened the center bolt and took off the old Idler pulley. It looked brown in the middle and didn't roll well. But I wasn't sure if that was it, because the noise was so loud and sounded metal on metal. So I checked everything and vacuumed everything. After I got the new part it took me about 5 minutes to put the new one on. And dryer works fine. Thanks for the quick response and I saved about $200.00!

I Took the front off and saw the cushion was gone around the drum and glids were worn down. I ordered both parts . It took 5 minutes to glue the cushion back on around the drum and 2 minutes to snap the drum glids on.But what I couldnt believe was the amount of lint that was all over the inside of the dryer.I would suggest to anyone to take the dryer front off once a year and clean it all out . I now understand fully why there are dryer fires.But the fix was cake and it runs like new.

Installed just like the video described and it went quite well. The part arrived in a short amount of time and the belt was exactly what I needed.Thank you I will visit your web site again. A very satisfied customer. :) Veronica G.

The belt arrived in 2 days. I cleaned the inside and it took no time to replace the belt. All I did is removed the front.The video was very helpful.Your magnet is on my refrigerator for future orders. Thanks.....Andy

1. Use flat blade to compress clips so top could be raised. Use Philips to remove 2 screws holding front on. Popped front off and then removed old worn and broken glides. Had to lift the drum slightly when placing the front back on. Screwed in the 2 screws to hold the front on. Lowered and locked top. Be careful not to pinch any wires..

I suspected a worn belt and that's what it was. I watched 2 videos on belt replacement and it was not a hard fix. The only "problems" I could foresee would be moving the drum around if you are not that strong. Its not terribly heavy, just a little awkward. I also sliced the top of my hand a little on the underside of the cabinet when moving the drum. Being a little more careful that wouldn't have happened. Part plus shipping was less then $20, and we now have a great working dryer again. I also got a zap when I forgot I had plugged it back in and was putting the inside screws back and the screwdriver crossed some wires. Nothing bad, just a quick jolt. Remember to unplug it until you're all done!

I viewed a video online and my repair was as simple as the video showed. Love that I am able to do quick fixes like this! Thanks Partselect.com!

so easy my daughter installed it the video was very helpful

Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!

Pulled front off dryer, popped the top up, took belt off pulley, pulled drum up and out just far enough to pull element out and put new one in. Very easy and quick. PartSelect always sends good quality parts and very quickly. I will use them for all my repairs.

I replaced it...just popped it in.

Used a flathead screw driver to pry broken handle out and snapped new handle right back in. Took no time at all. It was great and to top it off, I received the ordered item within 2 working days! Thanks so much. (I do not really know the age of the dryer as it belonged to my Mother who has been relocated into Hospice).

Raised the lid, removed 2 little screws,slipped the front panel off, disconnected the safety switch, vacuumed everything, slipped on the drive belt and reversed my way out. It was way more easy than filling a grease gun!

remove 2 screws rear of drier at top slid the top back and off removed 4 screws on front electronic read out panel and disconnected two wire harness plugs remove the panel removed 2 screws for lower panel at top on either side of rotating drum,tilted machine back removed two screws at very bottom on front of dryer to remove lower panel ,and remove the lower 2 screws to remove front panel.lifted rotating drum up and out of drier ,removed 4 wires on the heating element and four retaining screws from rear of drier to releases the heating element,than reverse the procedure for assembly.