KER331ZAS0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- andrei from Clifton, NJ
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken belt
The belt arrived in 2 days. I cleaned the inside and it took no time to replace the belt. All I did is removed the front.The video was very helpful.Your magnet is on my refrigerator for future orders. Thanks.....Andy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from McCalla, AL
- Parts Used:
- 134120900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer had no power. After doing quick troubleshoot determined Thermal Limiter was the problem
Removed top from dryer. Saw I could get to Limiter without removing dryer drum.Removed Limiter with phillips head screwdriver and wires with needle nose pliers. Replaced wires and secured Limiter to dryer works like a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MANUEL from SAN JACINTO, CA
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum belt
so easy my daughter installed it the video was very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caryn from San Diego, CA
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drum stopped spinning with any kind of load
I suspected a worn belt and that's what it was. I watched 2 videos on belt replacement and it was not a hard fix. The only "problems" I could foresee would be moving the drum around if you are not that strong. Its not terribly heavy, just a little awkward. I also sliced the top of my hand a little on the underside of the cabinet when moving the drum. Being a little more careful that wouldn't have happened. Part plus shipping was less then $20, and we now have a great working dryer again. I also got a zap when I forgot I had plugged it back in and was putting the inside screws back and the screwdriver crossed some wires. Nothing bad, just a quick jolt. Remember to unplug it until you're all done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from ANCHORAGE, AK
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer spun but didn't heat.
It was a closet type washer/dryer combo. With little space to work I needed to know how to get at the heating element to test it. Was told the tumbler had to come out the front to expose the element. Made the job easy without having to figure that out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Enterprise, AL
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer stopped putting out heat.
The repair went very well for a 1st timer. Instructions were very easy to follow. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Minot, ND
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken belt
Remove drum, replace belt, return drum
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Raritan, NJ
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer not heating up and shutting down
remove 2 screws rear of drier at top slid the top back and off removed 4 screws on front electronic read out panel and disconnected two wire harness plugs remove the panel removed 2 screws for lower panel at top on either side of rotating drum,tilted machine back removed two screws at very bottom on front of dryer to remove lower panel ,and remove the lower 2 screws to remove front panel.lifted rotating drum up and out of drier ,removed 4 wires on the heating element and four retaining screws from rear of drier to releases the heating element,than reverse the procedure for assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Cocoa, FL
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Belt
Brought up repair video on my smart phone and followed instructions while doing the repair (pausing when needed) and completed the job in under an hour including vacuuming the lint from inside the dryer before re-assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Carmel, IN
- Parts Used:
- 134120900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer over heated tripped thermal limiter
Took apart dryer and replaced limiter located on back, reassembled dryer and tested wiithout connecting to vent. Dryer working fine without vent connection. However as always something simple turns to disaster when children help. While cleaning out lint from dryer vent which I will say was the original problem causing the limiter to trip, youngest son wanted to help. Son did not know that to walk in an attic you must step on joists not drywall. No one was hurt just banged up falling into the garage. Extended repair to ceiling added dificulty factor of 2 days and a bit of insulation clean up. Good news is the dryer works fine and the vent is no longer clogged up with lint. Watch your help it always adds to the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Lakeland, FL
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Heating Element Failed!
I youtube'd the repair, and repaired it! While I was at it I replaced the belt! (Highly recommend replacing the belt while you are replacing the element!) Was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from LOXAHATCHEE, FL
- Parts Used:
- 134503600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Belt & drum bearing
Had the drum bearing but had never got a round to putting it in we just let it squeek. Then the belt went. Easy enough, whatched the tutorial once and just did it. 35 minutes and back drying.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Iowa City, IA
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dryer was not heating
We followed the how-to video. It was actually easier than the video made it look. Our dryer had a removable panel behind the pulley to put the belt back on easier. We had to take the whole dryer apart, but it was not difficult at all. We replaced the heating element and put it back together. If you can screw a screw, you can do this repair. Our dryer is working good as new. I love this site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from North Port, FL
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Heater Not Working
I never respond to any of these surveys, but in this case ill make an exception because they made it so easy and parts were received correctly a quickly. Thanks, dan
Was this instruction helpful to you?
Thank you for voting!