KER331ZAS0 Frigidaire Dryer - Instructions

Opened top and screwed the front off. Put belt around drum. It took two times as my sweet husband put the belt on backwards the first time.

Installed just like the video described and it went quite well. The part arrived in a short amount of time and the belt was exactly what I needed.Thank you I will visit your web site again. A very satisfied customer. :) Veronica G.

Unplugged dryer, Removed top of dryer, Removed electrical connection to thermal limiter, tested thermal limiter with meter and found that it was bad,removed defective limiter, ordered part, waited for part (1day), put new thermal limiter in dryer. reattached connections, put top of dryer back on, plugged in dryer, attempted dryer start up and it worked. Very easy because of the information I got on this site. Thank you

I heard the dryer running, but I didn't hear it tumbling like usual, so I got suspicious. I popped the top off of the dryer to reveal a broken belt. Installation took 20 minutes.

I have used this company twice now and both times have been a good experience. Would highly recommend!

I followed the vidio from yor web site it was great without it i would still be trying to get done.

Once the part arrived, I logged back into my order and watched the part installation video as I did the repair. The video was perfect, it made doing the repair easy and safe. Best part is I didn't end up with any extra screws which was good.

Many thanks for the video you guys put together on replacing dryer belts! I didn't know how I was going to get inside the dryer. I had the dryer apart in 10 minutes! Had to wait a day for the belts to come in. New belt in and dryer running in 15 minutes! Thanks for running a first class operation!! Jim

disconnected the dryer; cleaned the duct. I reconnected everything and started it up again and within seconds tripped the breaker.Decided probably the thermal limiter was faulty, so ordered new one from you. After it arrived I watched video, then removed the top and front, pulled drum to give me some workroom, replaced the limiter, reassembled in reverse order.I then reset the breaker, plugged the dryer in. Runs perfect.The drum was a challenge - so I used a wooden wedge to support from the front and opened the 12 by 12 rear port to access and reset the pulley cable assembly.

Removed top from dryer. Saw I could get to Limiter without removing dryer drum.Removed Limiter with phillips head screwdriver and wires with needle nose pliers. Replaced wires and secured Limiter to dryer works like a new one.

I suspected a worn belt and that's what it was. I watched 2 videos on belt replacement and it was not a hard fix. The only "problems" I could foresee would be moving the drum around if you are not that strong. Its not terribly heavy, just a little awkward. I also sliced the top of my hand a little on the underside of the cabinet when moving the drum. Being a little more careful that wouldn't have happened. Part plus shipping was less then $20, and we now have a great working dryer again. I also got a zap when I forgot I had plugged it back in and was putting the inside screws back and the screwdriver crossed some wires. Nothing bad, just a quick jolt. Remember to unplug it until you're all done!

Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!

With drum not turning, I removed rear access panel and confirmed that the belt was missing from the motor pulley. The instructional video provided by PS was extremely helpful. It made the job simple. Removal of drum thru front frame was the most difficult part which was relatively easy. Once the front panel and drum were removed, I could then see that the front drum top glide nylon/felt strip needed replacing which I then obtained.

Used wiring diagram in back of machine control head. UNPLUG DRYER! Removed panel off control head and motor access cover at bottom of dryer. Tested door switch continuity first, then continuity from control timer to motor. Found open circuit on white wire. Opened top of machine (pops up at front) and found thermal limiter on back of machine was burned and caused open circuit. It's a little awkward to get to the screws with the drum in place. Use a 30º angle ratching 1/4" ratchet wrench with a magnetic #2 phillips bit.

Remove drum, replace belt, return drum