SAGQ7070KS0 Electrolux Dryer - Instructions

Very slowly and carefully, you tube videos and schematic very helpful.

Once we got the dryer out of the cramped where we could work on it, the project went a little quicker. I'd recommend using paper plates/bowls, that you label, to hold all the screws for each piece you remove off the back. It doesn't seem like it will be a lot, but we had at least 20-30 screws in 4-5 different sizes. Unlike someone else's install, we had to completely pull the white back panel off, as well as the main back cover, due to one screw holding the air duct from the inside of the dryer compartment (meaning we couldn't reach everything from the back). Getting this screw out was a challenge and seemed like a huge design flaw, but if you can't get to that screw, the old air duct isn't coming out. There are 2 other screws holding the air duct but they're easy to reach once the back panel is off.
Once that was taken out the process was straightforward, we just took our time reattaching everything step-by-step. Now our dryer works like new.

First i replaced the drum bushing on the rear of the drum ,it was definitely bad but noise was still there
Decided it was the blower assy , pulled the dryer out disconnected the power,took off the frt panel with the door, disconnected the wiring to motor remover motor and fan assy, most trouble i had was fan is on motor with reverse threads messed with removing fan until I figured out it was backwards after that removed old fan and housing installed new one ,put dryer back together,started it and only normal noises
Good for another 5 years
Chuck

Blower wheel came apart from molded-in nut, was loose, was rubbing on housing wall, and was likelynot moving to much air. I read some troubled stories about separating the wheel nut from the motor shaft so bought a new motor and blower housing and install wall pretty easy. There are videos on the teardown process and does that long and not alot of parts to keep track of either. I have already done the felt drum liner and rear drum ball and belt so if it's older than 15 years and your going to take the dryer apart, replace all these parts and you will about have new dryer at half the cost of new.

I seen a post on your website referring to the exact problem I was having. One of your staff recommended changing the control thermistor, which I did following the U-Tube video link you supplied. The repair went well and the dryer now operates perfectly ! Thanks for the accurate and helpful info.

I purchase one tube of heat resistant adhesive but I change both seals if you could afford to buy a second to I would recommend you do so the one tube just made it. For instructions on how to prepare the drum for installing new seals I went on YouTube

I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.

Cover of the dryer pops off and hinges back. Use a flat screw driver to pop the clips on the front sides. Two phillips head screws hold the front panel on. Remove them then lift the panel off the clips at the bottom. Two phillips head hold the Ignition Coil bracket in place. Take note of the direction of the cable connection, it's not marked. Dryer would ignite intermittently. Clothes were not dry after 1 hour.

Unplug dryer.
Put up the top of the dryer at the front, remove 2 screws holding the front of the dryer to the sides and remove front of dryer. Locate ignition coil on lower left. Remove 2 screws and bracket over the two ignition coils. Replace coils and reassemble in reverse.
Everybody's happy.

my experience was just like the other responses. top comes off, 2 screws and the front comes off and the screws to the solenoids come off. Replaced the solenoids and put everything back together.

All I had to do was pop in the new door catch. Works perfectly.

Removed burner, unpluged 2 plugs on coils. Removed 2 screws, replaced coils, pluged 2 plugs to coils replaced 2 screws. Reinstaled burner. Dryer works great.

Unplugged the electricity, turned off the gas, then pop open the top of the dryer. Removed the two screws and pulled the front of the dryer off. Removed the two screws that locked down the two m series ignition coils. Put it back together and all things worked great.

Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.

parts arrive just like they said they would .had parts installed with in 15 minutes was drying clothes thank you your advice was perfect.